how to wire two outlets together

Connect Outlets: Simple DIY Guide

By Rachel Davis
AD

Wiring electrical outlets might seem like a daunting task, but with the right knowledge and safety precautions, it can be a manageable DIY project. If you're planning to wire two outlets together, this guide will walk you through the process in a clear, step-by-step manner.

Before we dive into the process, let's discuss why you might want to wire two outlets together. This can be useful in situations where you need more outlets in a single location, like a kitchen counter or a home office. It's essential to ensure that you're not overloading the circuit and that all electrical work complies with local regulations and building codes.

Understanding Electrical Outlets and Circuits

It's crucial to understand the type of outlet you're working with and the circuit it's connected to. In the U.S., residential outlets are typically 125V, 15- or 20-amp circuits. Before starting, ensure you're working with the same type of outlet and that your circuit can handle the additional load.

AD
How to Wire an Outlet from Another Outlet (2 Methods & Steps)
How to Wire an Outlet from Another Outlet (2 Methods & Steps)
How to Wire an Outlet Off a Switch (7 Steps)
How to Wire an Outlet Off a Switch (7 Steps)
an empty room with the words how to add an outlet in 50 seconds on it
an empty room with the words how to add an outlet in 50 seconds on it

Outlets are usually wired using 14-3 or 12-3 non-metallic (NM) sheathed cable, which contains three insulated conductors: two hot wires (black and red), a neutral wire (white), and a ground wire (green or bare). Familiarizing yourself with these components will make the wiring process much easier.

Gathering Tools and Materials

Before you start, make sure you have all the necessary tools and materials. You'll need:

an electrical wiring diagram with two outlets and the words how to install kitchen outlets
an electrical wiring diagram with two outlets and the words how to install kitchen outlets
How to Wire Combo Switch & Outlet? Combo Device Wiring
How to Wire Combo Switch & Outlet? Combo Device Wiring
  • A non-contact voltage tester
  • Wire stripers
  • Needle-nose pliers
  • Wire connectors (wire nuts)
  • 14/3 or 12/3 NM cable (as needed)
  • Electrical tape
  • New outlet electrical boxes (if required)

Preparation and Safety

Always prioritize safety when working with electricity. Start by turning off the power to the outlets at your home's service panel. Use a non-contact voltage tester to ensure there's no power flowing to the outlets before proceeding.

Don't forget to wear appropriate safety gear, including safety glasses, and ensure that your work area is well-lit and clear of clutter. After you've finished wiring, have the work inspected by a licensed electrician to ensure it meets all safety standards.

AD

Wiring the Two Outlets Together

Now that you've prepared your workspace and gathered your materials, it's time to start wiring the outlets. The process involves connecting the hot, neutral, and ground wires from one outlet to the other, as well as connecting them to the power source.

If your outlets are already wired and in use, you may need to replace the existing boxes to accommodate the new wiring. Ensure the new boxes are securely fastened to the studs and that the outlets are level and aligned with the drywall.

Connecting the Hot Wires

Locate the hot wires (black and red) on the cables connected to the new and existing outlets. Strip about ¾ inch of insulation from each wire using your wire stripers. Connect the corresponding hot wires from both outlets using a wire connector (wire nut) by twisting the wires together clockwise and then screwing on the wire nut.

AD

Tighten the wire nut securely, ensuring that no wires are exposed. Repeat this process for the other hot wire. If you're connecting to a power source instead of an existing outlet, connect the hot wire from your new outlet to the power source's hot wire following the same process.

Connecting the Neutral Wires

Find the neutral wires (white) on the cables connected to the new and existing outlets. Strip the insulation from each wire and connect them using a wire connector (wire nut) as described previously. Just like with the hot wires, if you're connecting to a power source, attach the neutral wire from your new outlet to the power source's neutral wire.

The same pigtailing principle applies when connecting ground wires (green or bare). Strip the insulation and twist together the ground wires from both outlets (and the power source, if applicable). Secure the connection with a wire nut, ensuring no wires are exposed.

AD

Securing the Wiring

After all the connections are made, route the cable through the electrical boxes and secure it with appropriate cable clamps. Ensure that the wires are not bent at sharp angles, as this can damage the insulation and cause electrical issues down the line.

Stuff the electrical box with appropriate cable fillers or bubble insulation to ensure that no more than 12 inches of cable is visible inside the box. This helps maintain the integrity of the wiring and prevents overcrowding in the box.

Testing the Wired Outlets

With the wiring complete, it's time to test your handiwork to ensure everything is working correctly. Turn the power back on at your home's service panel and use a non-contact voltage tester to check that each outlet has power.

If your outlets are working as expected, the final step is to replace your outlet covers and admire your newly wired electrical outlets. If you encounter any issues, don't hesitate to consult a licensed electrician for assistance.

In our modern, ever-evolving world, having enough electrical outlets is essential for keeping up with technological advancements and daily demands. By learning how to wire two outlets together, you've gained a valuable skill that will serve you well in your home improvement endeavors. Happy wiring!

AD