how to wire 4 outlet box

How to Wire a 4-Outlet Box

By Andrew King
AD

Wiring a 4-outlet box may seem daunting, but with the right tools and knowledge, it's a manageable DIY project. This guide will walk you through the process step by step, ensuring safety and compliance with electrical codes.

Before you start, ensure you have the necessary tools and materials. You'll need a 4-outlet, non-metallic, surface-mount box, four 15-amp or 20-amp electrical outlets, 12/2 or 14/2 non-metallic (NM) sheathed electrical cable (Romex), wire strippers, and a voltmeter or multimeter for safety checks.

Planning Your Wiring

Before you begin, plan your wiring layout. Decide where each outlet will be positioned and ensure there's enough cable length to connect them. Keep in mind that all outlets should be tamper-resistant and within 6 feet of each other.

AD
How to Install a Junction Box
How to Install a Junction Box
How To Install 4 Outlets Into A 1 Gang Electrical Box! DIY
How To Install 4 Outlets Into A 1 Gang Electrical Box! DIY
wiring multiple outlets in series with two switches and one light switch on the same wall
wiring multiple outlets in series with two switches and one light switch on the same wall

Medica:

Choosing the Right Wire Gauge

For a 4-outlet box, you'll typically use 12/2 or 14/2 Romex, which is designed for 15-amp or 20-amp circuits. Here's a simple way to remember:

How to Wire an Outlet
How to Wire an Outlet
  • 12/2 for 20-amp circuits (most common in modern homes) and 12/3 for 20-amp, 3-wire circuits (when you need a third hot wire).
  • 14/2 for 15-amp circuits (found in older homes), and 14/3 for 15-amp, 3-wire circuits.

Never use 16/2 or 18/2 cables, as they're not designed for branch circuits and are not allowed by code.

Understanding Wire Colors

NM cable has a black, white, and green (or green with yellow stripe) sheath. Black and red indicate hot wires; white is neutral; and green (or green with yellow stripe) is ground. Always ensure you understand wire colors before starting to wire.

AD

Wiring the 4-Outlet Box

Now that you've planned and understood the basics, it's time to wire. Always ensure the power is off and test lines with a voltmeter or multimeter before starting.

To begin, feed the cable through the opening at the back of the outlet box. Here's how to wire the outlets:

Wiring the First Outlet

  1. Strip about 1.5 inches of sheathing from the NM cable, exposing the three individual wires.
  2. Strip about 3/4-inch of insulation from the ends of each wire.
  3. Connect the white (neutral) and green (ground) wires to the matching screws on the outlet. Tighten securely, without overtightening.
  4. Connect the black (hot) wire to one of the brass-colored screws on the outlet. The other brass screw will be used for the "line" (incoming) hot wire from the next outlet.

Wiring the Remaining Outlets

  1. For each subsequent outlet, connect the white and green wires as before, but connect the black wire to the other brass screw (marked "line").
  2. Pigtail (connect multiple wires to one single screw) the neutral and ground wires from the previous outlet to the new outlet. This ensures all wires are connected and the circuit is complete.

Once all outlets are wired, secure them in the box. Make sure the wires are not so long as to bend the outlets out of position, and the box doesn't become overfilled.

AD

Securing the Box and Wiring

Secure the box to the wall, ensuring it's level and safe to operate. Then, secure the wiring:

  • Use wire clamp screws to secure the wires inside the box, ensuring they're not stressed or damaged.
  • Position the outlets so they're level and flush with the wall.
AD