how to unclog whirlpool washer

How to Unclog Whirlpool Washer

By Michael Rodriguez
AD

If your Whirlpool washer is leaving you with soaking wet clothes and a frustrated disposition, don't despair. A clog is often the culprit, but with a bit of troubleshooting and some elbow grease, you can restore your washer to its spinning glory. This guide will walk you through how to unclog a Whirlpool washer, step by step.

First, it's crucial to understand that washer clogs aren't always about blockages that can be easily removed. They often stem from issues with the drainage pump or the drain hose. But before you dive into the complex realm of washer mechanics, let's start with the most common causes of clogs.

Identifying Common Causes of Clogging

Clothes, hair, lint, and other tiny particles can accumulate in your washer’s drain pump, essentially plugging the system and preventing water from draining. Additionally, a kink in the drain hose or a faulty pump can also cause the dreaded soaking wet clothes scenario.

AD
Your Whirlpool washer stuck on sensing fill? try these fixes
Your Whirlpool washer stuck on sensing fill? try these fixes
Whirlpool Washer Loc Error: Troubleshooting Guide
Whirlpool Washer Loc Error: Troubleshooting Guide
How to Unclog a Whirlpool Washer Water Inlet Valve: Step-by-Step Guide
How to Unclog a Whirlpool Washer Water Inlet Valve: Step-by-Step Guide

Before you begin, ensure your Whirlpool washer is unplugged from the power source. Safety first!

Checking the Drain Pump

The drain pump is a critical component that pushes water out of your washer. If it's clogged or faulty, your washer won't spin dry. To access the drain pump:

How To Unlock A Whirlpool Washer - Hunker
How To Unlock A Whirlpool Washer - Hunker
How to do a Whirlpool Washer Recalibration and More - Whirlpool Washer Troubleshooting Tutorial
How to do a Whirlpool Washer Recalibration and More - Whirlpool Washer Troubleshooting Tutorial
  1. Turn off the washer and unplug it from the power source.
  2. Locate the drain pump, usually behind the access panel at the bottom front of the washer.
  3. Remove the panel and disconnect the pump from its hose.

Inspect the pump for any visible blockages. If you find anything, use pliers or a screwdriver to remove it. If not, it might be time to consider a pump replacement.

Inspecting the Drain Hose

The drain hose, responsible for carrying water out of the washer, can sometimes kink or clog. Here's how to check it:

AD
  1. Disconnect the hose from the back of the washer and from the drain.
  2. Straighten the hose to check for any kinks. If you find one, gently bend the hose back into a smooth curve to resolve it.
  3. Inspect the hose opening for any signs of clogging. If there are, use a wire hanger or a length of clothing to gently unclog it.

Once you've checked these common causes, you're well on your way to diagnosing the problem. But what if neither the pump nor the hose is the culprit? Let's delve into some less common causes.

Troubleshooting Less Common Issues

Sometimes, the issue might be with the drain filter, the lid switch, or even the dash panel. Let's explore these possibilities.

Cleaning the Drain Filter

The drain filter, often found behind a small panel at the bottom of your washer, can become clogged with lint and debris over time. A good clean can often resolve a that won't spin situation.

AD
  1. Consult your Whirlpool washer manual to locate the drain filter access panel.
  2. Open the panel and remove the filter. It might require a screwdriver to unscrew it.
  3. Clean the filter under running water, removing any debris or lint you find.
  4. Replace the filter and test your washer.

Checking the Lid Switch

The lid switch ensures that your washer won't run without the lid closed. If it's faulty, it could prevent the washer from entering the spin cycle. Here's how to replace it:

  1. Consult your Whirlpool washer manual to locate the lid switch, typically behind the control panel.
  2. Remove the control panel (you might need a screwdriver) and disconnect the switch from its wiring.
  3. Replace the switch with a new one, ensuring it's correctly polarized.

After troubleshooting these less common issues, your Whirlpool washer should be back in business. But if your washer is still leaving your clothes soaking wet, it might be time to call in a professional. Regular maintenance can help prevent clogs and other issues, so don't forget to clean your washer regularly and remain vigilant for signs of trouble.

Just like that, you've tackled the dreaded unclogging issue and restored your Whirlpool washer to its spinning best. Now, go forth and launder with confidence!

AD
AD