how to thread kobalt weed eater

"How to Thread a Kobalt Weed Eater"

By Andrew Anderson
AD

Tackling weeds around your home can be a challenging task, but with the right tool, the job becomes significantly easier. One of the most popular tools for this task is the Kobalt weed eater. Known for its durability and performance, learning how to thread a Kobalt weed eater can help you maintain a well-trimmed lawn all year round. In this guide, we'll walk you through the process step-by-step.

Before we begin, it's essential to have the right tools. For threading your Kobalt weed eater, you'll need the following:

Understanding Your Kobalt Weed Eater

The first step in maintaining your Kobalt weed eater is understanding its parts. The trimmer line, also known as 'string' or 'monofilament', is housed in a spool inside the weed eater's head. This line is what actually cuts the weeds. When you run out of line, you'll need to replace it, a process known as 'threading' your weed eater.

AD
How to change the string on the Kobalt Cordless String Trimmer Model #KST
How to change the string on the Kobalt Cordless String Trimmer Model #KST
Kobalt 40v Trimmer String Replacement
Kobalt 40v Trimmer String Replacement
How to replace reload string on Kobalt 40V trimmer
How to replace reload string on Kobalt 40V trimmer

Kobalt weed eaters use either 0.065-inch or 0.080-inch line. Ensure you purchase the correct size to avoid damaging your tool.

Preparation

Before starting, ensure your Kobalt weed eater is turned off and cooled down if it has been in use. Disconnect the spark plug wire for safety, and place your weed eater on a stable, flat surface.

Gather your tools - the new spool of trimmer line, a coin or flathead screwdriver, and your Kobalt weed eater.

Removing the Old Spool

Begin by finding the end of the trimmer line. If it's not already wound around the spool's hub, you can usually find it near the outside of the spool. Wrap the line around the hub to secure it, then remove the protective cap or cover on the side of the weed eater's head.

AD

Next, use a coin or screwdriver to turn the spool release button or nut (usually located on top of the spool) counterclockwise. This will release the spool from its lock. Pull the spool and the entire line out of the weed eater's head. Wind the used line onto itself to prevent tangling.

Threading the New Line

With the old spool removed, it's time to install the new one. Start by removing the new line from its packaging, ensuring you have the correct size for your Kobalt weed eater. Unwind enough line to create an 'X' shape around the spool's hub, with the two ends crossing in the center.

Winding the Line

Begin winding the line around the spool's hub, ensuring it goes in the same direction as the arrow printed on the spool. This arrow indicates the direction the line needs to feed out during operation. Wind the line tightly against itself, preventing it from unwinding when in use.

AD

Wind the line around the hub until you reach the point where the spool's end meets the hub. Leave about 6 to 10 inches of line hanging from the last wrap. This line will be cut to size once the spool is reinserted into the weed eater's head.

Reinserting the Spool

Look for the hole on the side of your Kobalt weed eater's head where the spool will fit. Align the spool with this hole and insert it until it's secure. Replace the protective cap or cover, ensuring it's locked into place.

Reconnect the spark plug wire if you disconnected it earlier. Now it's time to trim the line to the correct length. Place the weed eater on the ground, and hold the shroud or cutting head against it. With the trimmer head on the ground, press the trimmer's trigger to cause the trimmer line to stick out slightly from the cutting head. This line length should be roughly 1 inch for most models.

AD

Trimming the Line

Once the trimmer line sticks out the correct length, release the trigger to stop the line from spinning. Use a pair of scissors to trim the line against the cutting head, ensuring both sides are even. This will give you clean, powerful cuts when you start trimming again.

Your Kobalt weed eater is now ready to tackle your weeds! Remember to store your weed eater properly when not in use and to replace the trimmer line every 4 to 6 hours of operation for optimal performance.

Happy trimming, and may your lawn always be the envy of the neighborhood!

AD