how to take apart moen shower head

How to Disassemble a Moen Shower Head

By Daniel Taylor
AD

Tired of hard water stains or mineral buildup affecting your Moen shower head's performance? It's time to take apart your Moen shower head for a thorough clean or replacement. Don't be intimidated; with the right tools and steps, you can disassemble and reassemble your Moen shower head with ease. Here's a comprehensive guide on how to take apart your Moen shower head.

Before we start, gather your tools: aAllen wrench orhex key (depending on your Moen model), a pair of slip-joint pliers, and a towel or basin to catch any water. Also, ensure your shower is turned off and the water supply is disconnected to prevent unexpected water sprays.

Preparation: Turning Off Water Supply & Removing the Shower Head

Begin by turning off the water supply to your shower. The valve is usually located behind the shower access panel or in the basement. Once the water is off, open the shower faucet to release any remaining water pressure. Then, using an Allen wrench (for Moen's популярнаяAttractive series) orhex key (for other models), loosen and remove the shower arm nut that connects the shower head to the shower arm.

AD
How To Remove Flow Restrictors On A Moen Shower Head - Hunker
How To Remove Flow Restrictors On A Moen Shower Head - Hunker
How to Remove Water Restrictor From Moen Shower Head in 5 Minutes
How to Remove Water Restrictor From Moen Shower Head in 5 Minutes
How to Replace a Shower Head: 8 Easy Steps
How to Replace a Shower Head: 8 Easy Steps

Next, twist and pull the Moen shower head gently to disconnect it from the shower arm. If it's stuck, use slip-joint pliers to grip and rotate the shower head, taking care not to damage the finish. Once disconnected, place the shower head in a secure, easily accessible location.

Disassembling the Shower Head

Moen shower heads typically come apart in three components: the outer shell, the clawed prong (or rubber washer), and the filter/chrome trim piece. Start by inspecting the bottom of the shower head. You'll notice one or more set screws. These are what's holding the shower head together.

How to Install Shower Head with Hose | Moen Magnetix Shower Head
How to Install Shower Head with Hose | Moen Magnetix Shower Head
How To Replace An Old Or Damaged Shower Head - The DIY Life
How To Replace An Old Or Damaged Shower Head - The DIY Life

Using your Allen wrench orhex key, turn the set screws counterclockwise to loosen and remove them. As you remove each screw, the shower head components will start to separate. Some models may have two sets of screws; make sure to remove all screws to completely disassemble the shower head.

Cleaning the Components

Now that your Moen shower head is disassembled, it's time to clean each component thoroughly. Soak the parts in vinegar to help dissolve mineral deposits and stains. For stubborn buildup, use a soft-bristled brush or cotton swabs to scrub gently. Inspect each piece for any cracks or damage, and replace if necessary.

AD

Don't forget to clean the shower arm and the connector as well. Soak them in vinegar, too, then scrub them clean using a brush or cloth. This will ensure a smooth reassembly and better water flow.

Reassembly: Putting Your Moen Shower Head Back Together

Once all components are clean and dry, it's time to reassemble your Moen shower head. Remember the order in which you removed the parts, or refer to the corresponding diagrams in your Moen user manual.

Start by reattaching the shower head to the shower arm. Apply a bit of plumber's tape around the shower arm threads to create a better seal. Then, hand-tighten the shower head onto the shower arm, ensuring it's securely attached but not overtightened.

AD

Reattaching the Shower Head Components

Begin reassembling the shower head components in reverse order. Start with the outer shell, followed by the clawed prong or rubber washer, and finally, the filter/chrome trim piece. As you reattach each component, ensure the set screws are properly aligned.

Tighten the set screws using your Allen wrench orhex key. Be careful not to overtighten, as this could damage the shower head internal mechanisms. Refer to your Moen user manual for specific torque recommendations.

Foclip; Reconnecting the Water Supply

Once the shower head is reassembled and reconnected to the shower arm, it's time to reconnect the water supply. Open the shutoff valve slowly to allow water to flow back into the shower line. Check for any leaks around the shower head connection.

AD

Test the shower head by turning on the water and adjusting the flow as needed. If everything is working correctly, you've successfully taken apart and reassembled your Moen shower head!

Regular maintenance is key to keeping your Moen shower head in optimal condition. Consider disassembling and cleaning your shower head every 6-12 months to remove mineral buildup and ensure proper water flow. Happy relaxing!

AD