how to take apart a psp

How to Disassemble a PSP: A Step-by-Step Guide

By Joshua White
AD

Ever found yourself with a faulty PSP, wishing you could open it up to fix the issue yourself? It's not as daunting as it sounds. With the right tools and knowledge, you can take apart a PSP and potentially save yourself some money. Let's dive into a step-by-step guide on how to disassemble your PSP.

Before we begin, remember that opening your PSP will void its warranty, and there's a risk of damaging it if you're not careful. This guide assumes you're comfortable with basic tool usage and understand the risks involved.

Required Tools

The first step is gathering your tools. You don't need much: a small Phillips #00 screwdriver, a plastic opening tool (like the one that comes with most electronics), and a small, flat-bladed tool for prying.

AD
a video game system sitting on top of a table with the caption fixing a broken screen for a psp 100
a video game system sitting on top of a table with the caption fixing a broken screen for a psp 100
How to take apart your PS5 Controller and fix Stick Drift
How to take apart your PS5 Controller and fix Stick Drift
How to Clean a Sony PSP
How to Clean a Sony PSP

You might also want some tweezers to help with small parts, and a container to keep all your screws and parts organized. Lastly, turn off your PSP and remove any batteries or power sources to prevent any electric shocks.

Removing the Back Cover

Starting with the simplest part, let's remove the back cover. Use your plastic opening tool or a guitar pick to insert it into the small gap at one of the bottom corners of the PSP. Gently slide the tool along the edge until you hear a click, then repeat on the opposite side.

How To Replace The Battery in a Sony PSP 3000
How To Replace The Battery in a Sony PSP 3000
✨ Discover the Best Trending & Winning Products!
✨ Discover the Best Trending & Winning Products!

The back cover should now pop off. If it's still stuck, you can gently use the flat-bladed tool to pry it up from one edge. Be careful not to damage the plastic.

Removing the Internal Screws

Now that the back cover is off, you'll see several screws holding the internals in place. Use your Phillips #00 screwdriver to remove these screws. There are nine of them, so keep track of where they go.

AD

Once all the screws are out, set them aside in your container. Make sure they stay somewhere safe, as you'll need to put them back in when you're reassembling your PSP.

Removing the Motherboard

The motherboard is held in place mainly by the screws you just removed, but there are also some clips keeping it in place. To release the clips, use your plastic opening tool or a small flat-bladed tool to gently press down on the sides of the board. You should feel it click into place.

Lift the motherboard out carefully. It's still connected to the screen via a ribbon cable. Don't worry about this for now; we'll deal with it later.

AD

Removing the Screen

The screen is held in place primarily by a bracket at the top. To remove it, you'll need to carefully pry it up from the bottom. Use your flat-bladed tool to slowly work your way around until the screen pops off.

Again, be careful with the ribbon cable connecting the screen to the motherboard. Don't pull on it, as you could damage it. Instead, gently pull on the connector to detach it from the board.

Removing the UMD Drive

The UMD drive (Universal Media Disc) is held in place by two screws at the bottom. Remove these with your screwdriver, then use your flat-bladed tool to gently pry the UMD drive out from the top.

AD

As you lift it out, you'll see a cable connected to the side. This is a flexible printed circuit (FPC) cable, and you can disconnect it by gently lifting the tab on the connector up and then pulling the cable straight out.

Removing the Control Stick and Face Buttons

If you want to remove the control stick and face buttons, start by removing the plastic stick itself. Just pull it straight up. Underneath, you'll see a screw. Remove this with your screwdriver, then use your flat-bladed tool to gently pry up the button assembly.

The stick and buttons are connected to the motherboard via two ribbon cables. Disconnect these by gently lifting the tabs on the connectors up and then pulling the cables straight out.

That's it! You've successfully disassembled your PSP. Reassembling it is essentially the reverse process. Just make sure to line everything up correctly and apply the same amount of pressure when reattaching parts.

Now that you know how to take apart a PSP, you can confidently tackle repairs or modifications. Just remember: disassembly is the easy part. It's the reassembly that requires patience and careful attention to detail. Happy tinkering!

AD