how to take a lasko tower fan apart for cleaning

Lasko Tower Fan Cleaning: Step-by-Step Disassembly Guide

By Richard Davis
AD

Tired of your Lasko tower fan gathering dust on every corner? It's time to give it a thorough cleaning to ensure it performs optimally. In this guide, we'll walk you through the process of taking your Lasko tower fan apart for a complete, top-to-bottom cleaning. By following these steps, you'll not only restore your fan to like-new condition, but also extend its lifespan.

Before we begin, ensure you have all the necessary tools at hand: a screwdriver (usually Phillips or flathead, depending on your model), a cloth or brush for dusting, a bowl of warm soapy water for deep cleaning, and a dry towel for drying. Once you've gathered your supplies, let's dive into the disassembly process.

Disassembling Your Lasko Tower Fan

The first stage of cleaning your Lasko tower fan involves taking it apart. Follow these steps carefully to avoid damaging any components.

AD
How to Clean a Tower Fan — The Family Handyman
How to Clean a Tower Fan — The Family Handyman
How to Clean a Tower Fan
How to Clean a Tower Fan
Tower fan cleaning with leaf blower | Lasko fan cleaning
Tower fan cleaning with leaf blower | Lasko fan cleaning

Remember, tower fans have multiple parts, and it's essential to keep track of where each component goes. Take a few photos as you disassemble to help you reassemble later.

Removing the Grille and Oscillation Mechanism

Begin by unplugging your fan from the power source. Then, remove the grille at the front of the fan. Most Lasko models have a simple snap-fit grille that can be gently pried off. Some models may require unscrewing the grille first.

How To Clean A Lasko Tower Fan | Without Opening it Up
How To Clean A Lasko Tower Fan | Without Opening it Up
How to Clean a Tower Fan: A Complete Step-by-Step Guide to Extend Its Life - Aosom
How to Clean a Tower Fan: A Complete Step-by-Step Guide to Extend Its Life - Aosom

With the grille removed, you'll see the oscillation mechanism. Using your screwdriver, loosen and remove the screws securing the oscillation mechanism to the base. Once the screws are out, carefully lift the mechanism off the base.You may need to wiggle it gently to free it from the housing.

Disconnecting the Motor and Control Panel

With the oscillation mechanism removed, you'll have access to the motor and control panel. Unplug the wiring harness connecting the control panel to the motor.

AD

Next, locate the screws holding the motor assembly to the base. Remove these screws and gently lift the motor assembly out of the base. Be careful not to strain any wires. It might help to disconnect the power cord from the motor at this stage.

Cleaning Your Lasko Tower Fan

Now that your Lasko tower fan is in pieces, it's time to give each component a thorough clean. Here's how to approach each part.

Throughout the cleaning process, ensure you're working in a well-lit area with a steady hand. Some components are fragile, so be gentle.

AD

Cleaning the Grille and Oscillation Mechanism

The grille and oscillation mechanism are the dustiest parts of your fan. Start by using a cloth or brush to remove excess dust. Pay close attention to the gaps between the grille's blades, as dust tends to accumulate here.

For a deeper clean, dip a cloth or brush in your bowl of warm soapy water and gently clean the grille and oscillation mechanism. Use a soft touch to avoid damaging the components. Rinse the components thoroughly and allow them to dry completely before reassembly.

Cleaning the Motor and Control Panel

The motor and control panel shouldn't require as much attention as the grille and oscillation mechanism. However, it's still essential to give them a gentle clean.

AD

Use a slightly damp cloth to wipe down the motor and control panel. Avoid getting the electrical components too wet. After cleaning, dry off any residual moisture immediately.

Cleaning the Base

The base of your fan is unlikely to be very dirty, but it's still worth a quick clean. Wipe it down with a damp cloth, then dry it off.

If you notice any stubborn stains or dirt, use a mild cleaning solution and a soft brush, but avoid harsh chemicals that could damage the finish.

Reassembling Your Lasko Tower Fan

With all components clean and dry, it's time to put your Lasko tower fan back together. Follow these steps in reverse order to the disassembly process.

As you reassemble, take your time and ensure each component is secured correctly. If you're at any point unsure, consult your photos from the disassembly process.

Securing the Motor and Control Panel

Begin by reconnecting the wiring harness between the motor and control panel. Ensure the connection is secure and the wires aren't straining.

Next, position the motor assembly in the base and secure it with the screws you removed earlier.

Securing the Oscillation Mechanism and Grille

Replace the oscillation mechanism in the base and secure it with the screws you removed earlier. Ensure the oscillation mechanism is properly aligned and functioning.

Finally, snap the grille back onto the fan or secure it with screws if your model requires it. Plug your fan back into the power source, and you're ready to enjoy your sparkling clean Lasko tower fan.

Regular cleaning is the key to keeping your Lasko tower fan in top condition. We recommend cleaning your fan every few months, or more frequently if you use it in a smoky or dusty environment. Happy cleaning!

AD