how to start a snowblower with old gas

Reviving Your Snowblower: How to Start With Old Gas

By Daniel Thomas
AD

Winter's icy grasp often means battling snowdrifts, and a well-maintained snowblower is your trusty ally. But what if your snowblower has been idle with old gas inside? Fear not! With the right steps, you can reanimate your snowblower and be ready to tackle those wintery regions. Let's delve into the process of starting a snowblower with old gas.

First, understand that old gas can cause issues due to ethanol content, which absorbs moisture. This can lead to gurgling sounds, poor performance, and even prevent your snowblower from starting. However, all hope is not lost. With patience and careful steps, we can revive your snowblower.

Preparing Your Snowblower

Before attempting to start your snowblower, ensure it's suitable for use. Check the tires, fuel lines, and all moving parts. Address any wear or damage to prevent further issues.

AD
How To Drain Gas From Snowblower The Easy Way
How To Drain Gas From Snowblower The Easy Way
Step By Step Guide On How To Drain Gas From Snowblower
Step By Step Guide On How To Drain Gas From Snowblower
Starting a Snowblower With Old Gas
Starting a Snowblower With Old Gas

Next, locate your snowblower's fuel valve. It's usually near the gas tank and is often red. Turn it to the 'off' position to prevent fuel from flowing while you work on it.

Removing Old Gas

Begin by removing the old gas. First, unscrew the fuel cap and place a container underneath the outlet to catch the old fuel. Empty the tank by siphoning the gas into the container using a siphon pump or a turkey baster.

Learn How to Drain Gas from Snowblower with 6 Effective Instructions
Learn How to Drain Gas from Snowblower with 6 Effective Instructions
How to replace a snowblower fuel line
How to replace a snowblower fuel line

Once you've removed as much gas as possible, it's time to prepare a fresh fuel mix. For most snowblowers, a mix of 89 octane or higher gasoline and stabilized fuel oil in a 40:1 ratio works well. Use fresh gasoline and a stabilizer designed for small engines to prevent future fuel-related issues.

Draining the Fuel Line

After removing the old gas, drain the fuel line to eliminate any remaining traces of the old fuel. Locate the fuel line, usually a clear plastic tube, and follow it to the engine to find its access point. Loosen the clamp holding the line and disconnect it from the engine.

AD

Let the remaining fuel drip into an appropriate container. Once most of the fuel has drained, reconnect the line. Make sure it's secure to prevent leaks when you refuel.

Starting Your Snowblower

Now that you've eliminated the old gas and prepared fresh fuel, it's time to start your snowblower.

First, turn the fuel valve back to the 'on' position. Then, take your new fuel mix and pour it into your snowblower's fuel tank. Fill it no more than 90% full to account for expansion and prevent fuel from overflowing.

AD

Priming Your Snowblower

Before starting, it's usually necessary to prime your snowblower to ensure fresh fuel reaches the carburetor. Find the primer bulb, often located near the fuel line, and squeeze it five to ten times. This sends fuel into the carburetor, preparing it for starting.

Once you've primed your snowblower, locate the starter handle or button and prepare to start it. It may take a few attempts, especially if the engine is frozen from inactivity. Be patient, and never force the starter to prevent damaging the machine.

First Start and Operation

After several attempts, assuming your snowblower is in good condition, it should start and run smoothly with fresh fuel. If it still won't start, double-check that you've followed each step correctly and there are no obvious issues with the machine.

AD

If your snowblower starts but runs poorly, try adjusting the choke. Fully enriching the mixture can help it run until the engine warms up and the old fuel is completely eliminated. Once it's running well, operate it bit by bit, clearing your driveway meticulously.

Remember, always operate your snowblower in well-ventilated areas and follow the manufacturer's guidelines for storage and care to extend its lifespan. Happy snow-battling!

AD