Reset TPMS Subaru Crosstrek: Step-by-Step Guide
Tire Pressure Monitoring System (TPMS) is a vital feature in your Subaru Crosstrek, ensuring safe driving conditions by alerting you to any sudden changes in your tires' air pressure. However, sometimes you might need to reset this system, for instance, after replacing a tire orrotating them. This article will guide you through the process of how to reset TPMS on your Subaru Crosstrek.
Before we dive into the reset process, it's essential to understand what the TPMS warning light means. If it's illuminated, it indicates that at least one of your tires has low air pressure. If it's flashing, it signifies a malfunction in the TPMS. Now, let's get started with the resetting procedure.
Understanding Your Subaru Crosstrek's TPMS
Your Subaru Crosstrek uses a direct TPMS, which means it measures the air pressure in each tire individualy and transmits this data to the vehicle's onboard computer. This system is more accurate and advanced than indirect systems that estimates pressure based on wheel rotation.
Your Crosstrek also has a TPMS warning light on the dashboard, usually next to the speedometer. This light will illuminate when air pressure in one or more tires falls below the recommended level by 25%. If the light comes on, it's crucial to check your tires' pressure immediately and adjust it as needed.
Understanding the TPMS Reset Light
The TPMS reset light on your Crosstrek's dashboard will flash for about one minute after ignition startup when the TPMS has been initialized successfully. If the light doesn't reset automatically, or if you've changed your tires, you'll need to perform a manual reset.
Before you begin, ensure that all tires are properly inflated to the recommended pressure for your vehicle. You can find this information in your owner's manual or on a label located on the driver's door jamb.
Preparing for the TPMS Reset
Before starting the reset process, you'll need to gather some items: a tire pressure gauge, an air compressor, and a screwdriver (for manual reset button). Make sure your Crosstrek is on a level surface and the ignition is in the "ON" position but the engine is off.
This process involves two stages: learning and memorizing the new tire sizes and pressures, and then resetting the TPMS itself. Let's first discuss the learning stage.
Learning and Memorizing Tire Sizes and Pressures
Your Crosstrek's TPMS needs to learn the new tire sizes and pressures. To do this, you'll need to inflate each tire to the recommended pressure and then drive at a steady speed for about 5-10 miles.
Here's a step-by-step guide to this process:
- Using the tire pressure gauge, ensure that all tires are inflated to the recommended pressure.
- Start your Crosstrek and drive at a steady speed of around 10-15 mph for about 10 miles. This allows the TPMS to learn new tire sizes and pressures.
- After driving, park your Crosstrek on a flat surface and turn off the engine. Wait for about 10 minutes to allow the tires to cool.
- Re-check the tire pressure after they've cooled. If it's still at the recommended pressure, proceed to the next section. If not, re-inflate or deflate as needed and repeat the driving process.
Resetting the TPMS on Your Subaru Crosstrek
Now that your Crosstrek has learned the new tire sizes and pressures, it's time to reset the TPMS. For this, you'll need to use either the "AUTO LEARN" mode (specific to your Crosstrek model) or the manual reset button (for older models). Let's discuss both methods.
Using the "AUTO LEARN" Mode: If your Crosstrek has the "AUTO LEARN" mode, follow these steps:
- Turn the ignition to the "ON" position without starting the engine.
- Press the "TPMS RESET" button located on the center console until the TPMS warning light flashes for about 3 seconds. Release the button.
- Listen for the "AUTO LEARN" ding sound, which signifies that the TPMS has been successfully reset. The warning light should turn off.
Using the Manual Reset Button: If your Crosstrek doesn't have the "AUTO LEARN" mode, you'll need to use the manual reset button. Follow these steps:
- Put your Crosstrek in "ACCESSORY" mode with the engine off.
- Locate the TPMS reset button, usually under the steering wheel or on the driver's side footwell.
- Press and hold the button for about 5 seconds until the TPMS warning light on the dashboard flashes.
- Release the button, then press it again briefly. The light should turn off, indicating that the TPMS has been successfully reset.
Congratulations! You've successfully reset the TPMS on your Subaru Crosstrek. Always remember to check your tires' pressure regularly for safe driving and to prevent unnecessary wear on your tires.
Don't forget that the TPMS is just one of the many safety features on your Crosstrek. Regular maintenance and staying informed about your vehicle's systems will help ensure you and your passengers' safety. Happy driving!