how to reset brother printer after replacing drum

Reset Brother Printer: Step-by-Step After Drum Replacement

By Sarah Young
AD

Imagine you've just replaced your Brother printer's drum, eager to get back to printing clear and quality documents. But alas, your printer isn't cooperating. Don't worry; it's probably just needs a reset to recognize the new drum. Resetting your Brother printer is a straightforward process, and this guide will walk you through it step by step.

Before we dive into the specifics, let's ensure you're working with a Brother printer that uses a pull-out control panel. Most Brother models use this design, but if your printer is an older model or a laser printer, the process might differ slightly. If your printer doesn't have a pull-out panel, consider checking the user manual or Brother's official support page for the correct reset proces

Understanding the Reset Process

Resetting your Brother printer involves two primary steps: turning off the printer and unplugging it from the power source, and then restoring power after a short duration. The printer will then initialize with the new drum. Sounds simple, right? Let's break it down further.

AD
How To Reset Drum On Brother Printer
How To Reset Drum On Brother Printer
How to Reset Drum on Brother Printer HL-L2370DW
How to Reset Drum on Brother Printer HL-L2370DW
How to Fix ''REPLACE DRUM'' Error Message on Brother Printer
How to Fix ''REPLACE DRUM'' Error Message on Brother Printer

Depending on the type of toner or ink installed, the reset process might require additional steps. For example, you might need to remove the cartridge, press the 'OK' or 'Stop' button, and then reinsert the cartridge. We'll cover these situations later in this guide.

Universal Reset Steps

Most Brother printers follow a universal reset process. Here's how to do it:

How to reset Drum on Brother HL 2270DW Printer HL 2220 HL 2230 HL 2240 HL 2250
How to reset Drum on Brother HL 2270DW Printer HL 2220 HL 2230 HL 2240 HL 2250
Brother HL Printer Not Working (How To Fix/Reset) - Ready To DIY
Brother HL Printer Not Working (How To Fix/Reset) - Ready To DIY
  • Power off your printer by pressing the 'Power' button on the control panel.
  • Unplug the power cord from the electrical outlet or surge protector.
  • Wait for at least 30 seconds, or better yet, a full minute. This allows the printer to discharge any remaining power.
  • Plug the power cord back into the electrical outlet or surge protector.
  • Power on the printer by pressing the 'Power' button on the control panel. The printer should initialize and recognize the new drum.

Resetting Inkjet Printers

If you're using an inkjet printer, the process is slightly different due to the nature of the cartridges. Here's what you need to do:

  1. Open the printer cover or front door to access the ink cartridges.
  2. Remove all ink cartridges.
  3. Follow the universal reset steps mentioned above.
  4. Reinsert the ink cartridges and close the printer cover or front door.
  5. The printer should now recognize the new cartridges and be ready for use.

Resetting Toner/Ink Based on Printer Model

While the basic steps usually work for all Brother printers, some models might have specific requirements. Let's look at some common scenarios based on your printer model.

AD

If your printer model isn't listed here, don't worry. The universal reset steps should still work. However, if you're unsure, it's always best to check your user manual or contact Brother's customer support.

Brother Laser Printers

For laser printers, you might need to hold down a specific button while turning on the printer. Here's how:

  1. Turn off the printer and unplug it from the power source.
  2. Locate the 'Go' or 'Stop' button on the control panel. For some models, you might need to unjam the paper path first.
  3. While holding down the 'Go' or 'Stop' button, plug the power cord back into the electrical outlet.
  4. Continue holding down the button until the printer completes the initialization process.
  5. The printer should now recognize the new toner cartridge.

Brother Ink Tank Systems

Brother's ink tank systems use a different process due to their design. Here's what you need to do:

AD
  1. Open the front cover of the printer and remove the ink tank.
  2. Wipe the ink tank Oh-auth to clean any ink residue.
  3. Follow the universal reset steps mentioned above.
  4. Reinsert the ink tank and close the front cover of the printer.
  5. The printer should now recognize the ink tank and be ready for use.

And there you have it, a comprehensive guide on how to reset your Brother printer after replacing the drum. The process is straightforward, and with a little patience, your printer should be up and running again in no time. Happy printing!

AD