how to replace washer hose

Easily Replace Your Washer Hose: Step-by-Step Guide

By Amanda Martin
AD

Has your washer started flooding your laundry room? It's likely due to a burst hose, a common issue that can be easily resolved by replacing the faulty component yourself. In this guide, we'll walk you through the step-by-step process of how to replace washer hose, saving you time and money. Let's dive in.

Before we proceed, ensure you have the right tools and supplies. You'll need a new washer hose assembly, pliers, an adjustable wrench, and a Phillips or flathead screwdriver. Safety first - unplug your washer and turn off the water supply valves at the wall before starting.

Identifying the Faulty Hose

The washer has two hoses - one for the hot water and one for the cold. First, locate the problematic hose. Look for any signs of leakage, bulging, or corrosion. Hot water hoses are typically red, while cold water hoses are blue.

AD
How to Remove a Washing Machine Drain Hose Safely
How to Remove a Washing Machine Drain Hose Safely
How to Remove and Replace Washing Machine Water Supply Hoses
How to Remove and Replace Washing Machine Water Supply Hoses
Rusty Washing Machine Hose Got You Stuck? Here’s the Easiest Way to Remove it
Rusty Washing Machine Hose Got You Stuck? Here’s the Easiest Way to Remove it

Once you've identified the faulty hose, it's time to disconnect it. Use your adjustable wrench to carefully loosen the hose from the water supply valve at the wall. Be gentle to avoid damaging the valve. Now, do the same at the washer end, releasing the hose from the inlet union. Have a towel or bucket ready to catch any water that may remain in the hose.

Preparing the New Hose

Your new washer hose assembly should come with a pair of stainless steel clamps. Position these clamps about an inch or two from each end of the new hose. Next, place the washer gaskets or rubber washers over the ends of the hose, ensuring they're properly seated.

How to Change Replace Washing Machine Hoses, the Right Way!
How to Change Replace Washing Machine Hoses, the Right Way!
How To Replace Tub-To-Pump Hose In Washing Machine?
How To Replace Tub-To-Pump Hose In Washing Machine?

If your new hose has an aerator screen, make sure it's facing the right direction - towards the water supply valve. This helps regulate water flow and prevent sediment buildup. Finally, ensure the hot and coldwater hoses won't get tangled or kinked when connected, which could lead to future issues.

Installing the New Hose

Now it's time to connect your new washer hose. Begin by attaching one end of the hose to the water supply valve at the wall. Make sure the arrow on the flex connector points towards the valve, complying with the direction of water flow. Hand-tighten the coupling, then use your adjustable wrench to gently tighten it further, taking care not to overtighten.

AD

Next, connect the other end of the hose to the inlet union on your washer. Again, ensure the arrow on the flex connector points in the direction of water flow. Hand-tighten the coupling, then use your wrench to gently tighten it. Once both ends are securely connected, use your pliers to tighten the stainless steel clamps in place. Be careful not to overtighten, as this could damage the hose.

Testing the New Hose

With your new washer hose installed, it's time to test it. First, reconnect your washer to the power source. Then, turn the water supply valves back on. Check for any leaks around the couplings at both ends of the hose. If everything is secure, your washer should now be ready to use.

Over time, it's a good idea to periodically inspect your washer hoses for any signs of wear or degradation. Catching potential issues early can prevent leaks and other costly problems down the road.

AD

And there you have it - replacing your washer hose is a straightforward task that anyone can handle. Not only have you saved money by doing it yourself, but you've also gained a useful skill. Now, go ahead and enjoy your newly repaired washer. Happy laundering!

AD