how to replace the heating element in a whirlpool dryer

**Step-by-Step: Replace Heating Element in Whirlpool Dryer**

By John White
AD

Dryers are essential appliances in our homes, but they can malfunction over time. One common issue is a defective heating element, which leaves your Whirlpool dryer unable to heat up and dry your clothes properly. Replacing the heating element is a straightforward process that can save you the cost of hiring a professional. Let's guide you through the steps to replace the heating element in your Whirlpool dryer safely and effectively.

Before we begin, ensure you have the following tools and parts ready: a Phillips screwdrivers, a nut driver, a multimeter (optional, for testing the old element), and the new heating element compatible with your dryer model. Always prioritize safety by unplugging your dryer from the power source before starting any repair work.

Identifying the Heating Element

The heating element in a Whirlpool dryer is usually located behind the front bulkhead, the large panel at the front of the dryer. It'spire-shaped and made of metal with a ceramic coating. Before ordering a replacement, identify your dryer's model number to ensure you get the correct heating element.

AD
How To Easily Test and Replace Your Whirlpool Dryer Heating Element WP3387747 – DIY Guide
How To Easily Test and Replace Your Whirlpool Dryer Heating Element WP3387747 – DIY Guide
How to replace heating element in Whirlpool electric dryer - dryer not heating
How to replace heating element in Whirlpool electric dryer - dryer not heating
Replacing a Heating Element on a Whirlpool Dryer
Replacing a Heating Element on a Whirlpool Dryer

To access the heating element, you'll need to remove the front bulkhead. Begin by unplugging the dryer and then removing the dryer's lower front panel using a Phillips screwdriver. Next, remove the screws securing the bulkhead to the dryer. With the screws removed, you can pull the bulkhead away from the dryer to expose the heating element.

Testing and Removing the Old Heating Element

Testing the Old Heating Element

Before removing the old heating element, you can test it with a multimeter to confirm it's faulty. Set your multimeter to the lowest resistance setting (usually 200 ohms or less) and touch the probes to the terminals of the heating element. If the reading is infinite or very high, the element is likely faulty and needs replacing.

Whirlpool Cabrio Dryer Heating Element Replacement Guide
Whirlpool Cabrio Dryer Heating Element Replacement Guide
Whirlpool Dryer Repair How To - Replace Heating Element
Whirlpool Dryer Repair How To - Replace Heating Element

If you don’t have a multimeter, you can skip this step and proceed to remove the old heating element. The process of removal will tell you if the element is faulty: if it's experimentally difficult to remove due to the element being welded onto the terminals, it's likely faulty due to overheating and expansion.

Removing the Old Heating Element

Once you've confirmed the heating element is faulty, it's time to remove it. First, disconnect the wire harness from the heating element. Then, use a nut driver to loosen and remove the mounting screws. You may need to use a putty knife or a flathead screwdriver to gently pry the element from its mounting bracket.

AD

If the element is stuck due to heat expansion, you might need to carefully use a claw hammer to gently tap it loose. Be cautious not to bend or damage the element further. Once removed, discard the old heating element responsibly.

Installing the New Heating Element

Before installing the new heating element, ensure it's the correct one for your dryer model. Installing the incorrect element can cause damage to your dryer and may void any existing warranties.

To install the new heating element, first position it in the mounting bracket and secure it with the screws you removed earlier. Ensure the screws are tightened securely but not overtightened, as this could damage the element.

AD

Reconnecting the Wiring Harness

After securing the heating element, reconnect the wiring harness to the terminals on the element. Ensure the connections are secure andtidying the wires neatly to prevent any interference with the dryer's operation.

Reassembling the Dryer

With the new heating element installed, it's time to reassemble your dryer. Start by replacing the front bulkhead and securing it with the screws you removed earlier. Then, replace the lower front panel and secure it with screws.

Finally, plug in your dryer and turn it on. Run a test cycle to ensure the heating element is working correctly and your dryer is functioning as it should. If the dryer heats up and dries your clothes properly, your repair is successful. If not, double-check your connections and ensure the heating element is the correct one for your dryer model.

AD

Regular maintenance of your dryer, including checking and replacing the heating element when necessary, can extend the lifespan of your appliance and keep it running efficiently. Always remember to prioritize safety when working on your dryer or any other appliance. If you're unsure about any step, don't hesitate to seek professional assistance.

AD