how to replace shower mixing valve

How to Replace a Shower Mixing Valve: Step-by-Step Guide

By Hannah Robinson
AD

Is your shower failing to maintain a consistent water temperature, or worse, leaking? The culprit might be a faulty shower mixing valve. Replacing it might seem daunting, but with the right steps and a keen eye for detail, it's a manageable task. Let's dive in and learn how to replace your shower mixing valve like a pro.

Before we start, remember that working with water systems requires caution. Always turn off the water supply and ensure the area is well-ventilated to avoid any potential water damage or gas buildup from improperly seated parts. Now, let's get started.

Gather Your Tools and Materials

Having the right tools and materials at hand ensures a smooth and efficient process. Here's what you'll need:

AD
How to Replace Two-Handle Shower Valve? | Replace Two-Handle With Showers
How to Replace Two-Handle Shower Valve? | Replace Two-Handle With Showers
How to Replace Mixing Valve Shower | 7 Simple Steps (2026)
How to Replace Mixing Valve Shower | 7 Simple Steps (2026)
a man that is standing in front of a wall with a box on it's side
a man that is standing in front of a wall with a box on it's side

  • Slip joint pliers
  • Adjustable wrench
  • Phillips or flathead screwdriver (depending on your valve configuration)
  • Tape measure
  • New shower mixing valve (ensure it's compatible with your existing water supply setup)
  • Teflon tape
  • Plumber's grease (optional)

a person is fixing a bathroom faucet with red handles and levers on the wall
a person is fixing a bathroom faucet with red handles and levers on the wall
an article in the magazine shows how to install shower mixers and faucets
an article in the magazine shows how to install shower mixers and faucets

Identify Your Valve Type

Before you start, identify the type of shower mixing valve you have. There are two common types: the cartridge valve and the ceramic disk valve. The process to replace them is slightly different, so it's essential to know which one you're dealing with.

AD

To identify the type, take a look at the control lever or handle. Cartridge valves usually have a single lever that controls both hot and cold water flow, while ceramic disk valves often have separate levers for hot and cold.

Turn Off the Water Supply and Drain the System

Locate the shutoff valves connected to your shower arm. They should be behind the access panel in the wall, underneath the shower, or in the basement or crawlspace. Turn them clockwise to shut off the water supply. To drain the water remaining in the pipes, open the shower faucet and leave it open until no more water comes out.

Remove the Old Mixing Valve

With the water supply turned off and the system drained, you're ready to remove the old valve. Here's how:

AD

Disconnect the Water Supply Lines

Use your adjustable wrench to carefully loosen and remove the pipes connected to both the hot and cold water supply lines. You might need to use pliers to grip the nuts securely. If the pipes are stuck, apply gentle force, but be careful not to damage them.

AD

Remove the Old Valve

With the water supply lines disconnected, the mixing valve should now be loose. Unscrew it counterclockwise and pull it out of the wall. If it's stuck, apply gentle pressure, but be careful not to damage the valve or the wall.

Install the New Mixing Valve

With the old valve removed, it's time to install the new one. The process is essentially the reverse of removing the old valve, but with some additional steps to ensure a proper fit and seal.

Prepare the New Valve

Before installing the new valve, wrap the threads with Teflon tape to prevent leaks. Wrap it clockwise, overlapping each layer by about half. This will ensure a watertight seal when you tighten the valve.

Install the New Valve

Aligned with the position of the pipe nipples on your wall, press the new mixing valve into place. Hand-tighten it as much as you can, then use a wrench to snug it up. Be careful not to overtighten, as this could strip the threads or crack the valve.

Reattach the Water Supply Lines

Reattach the hot and cold water supply lines to the new valve. Make sure they're tightly secured to prevent leaks. Use Teflon tape on the threads as well to ensure a watertight seal.

Test the New Mixing Valve

With everything connected and tightened, it's time to test the new mixing valve. Slowly turn the water supply back on at the shutoff valves. Check for any leaks around the connections.

Once you're confident there are no leaks, turn on the shower faucet and check the pressure and temperature. Adjust the new mixing valve as needed until you achieve the desired balance. Remember to replace any access panels you removed during the process.

Congratulations! You've successfully replaced your shower mixing valve. If you followed the steps carefully and took the time to ensure each connection was secure, you should now have a functioning shower with consistent water temperature. Should you encounter any issues, don't hesitate to consult with a professional plumber.

AD