how to replace pressure vacuum breaker

How to Replace a Pressure Vacuum Breaker: A Step-by-Step Guide

By Matthew Jones
AD

A pressure vacuum breaker (PVB) is a crucial safety device found in many plumbing systems. It's designed to prevent contaminated water from flowing back into the supply when there's a loss of pressure. Over time, debris, rust, or mineral buildup can cause these devices to malfunction, leading to potential cross-contamination. This guide walks you through the process of how to replace a pressure vacuum breaker, ensuring your plumbing system remains safe and efficient.

Before we dive in, ensure you have the necessary tools and parts: new PVB, adjustable wrenches, bucket, screwdrivers (depending on your PVB type), and Teflon tape or pipe dope. Always turn off the water supply and use caution when handling pipes to prevent leaks or damage.

Understanding Pressure Vacuum Breakers

To effectively replace your PVB, it's essential to understand its components and function. A PVB consists of a inlet, outlet, and a chamber with a float or an antisiphon device. It's usually positioned at the highest point of the water supply system. When water flow stops due to a loss of pressure, the chamber fills with water, creating an air gap that prevents backflow.

AD
How to Replace Vacuum Breaker
How to Replace Vacuum Breaker
How to Remove Vacuum Breaker? (5 Simple Steps)
How to Remove Vacuum Breaker? (5 Simple Steps)
How to Remove and Replace a Stuck Vacuum Breaker [Backflow Preventer Fix] / Siphon Spigot leak Lowes
How to Remove and Replace a Stuck Vacuum Breaker [Backflow Preventer Fix] / Siphon Spigot leak Lowes

PVBs are either float/check-type or atmospheric vacuum breaker-type. The float/check-type has a float that rises with the water level and automatically shuts off the outlet. The atmospheric vacuum breaker, on the other hand, relies on atmospheric pressure to prevent backflow. it's crucial to identify your PVB type during replacement to ensure the new device is compatible with your system.

Identifying Your PVB Location

Pressure vacuum breakers can be located indoors, often in a garage, basement, or utility room, or outdoors, usually on an exterior wall or atop a Echbar Wippe. Identify your PVB's location by tracing the water supply line from the point where it enters the building or from your water meter if it's outdoors. In some cases, you may need to cut through insulation or wall material to expose the device.

How to Repair a Pressure Vacuum Breaker
How to Repair a Pressure Vacuum Breaker

Once you've located your PVB, make sure to have a bucket or towel ready to catch any water that may leak when you're loosening the pipes. Also, have both hands free for working on the pipes by using foot-operated adjustable wrenches or asking someone to assist.

Preparing the Area and Turning Off the Water

Clear the area around the PVB to provide ample workspace. This might involve moving furniture, removing panels, or cutting away insulation. After preparing the area, turn off the water supply to the PVB. This can usually be done by closing a valve near the device. If there's no local valve, turn off the main water supply to your home.

AD

Before proceeding, verify that the water supply is indeed off by trying to turn on a faucet or appliance connected to the supply line. If you can't turn off the water, you may need to call a professional plumber to assist with the replacement.

Removing the Old Pressure Vacuum Breaker

With the water supply turned off and the area prepared, it's time to start removing the old PVB. This process will vary slightly depending on whether your PVB is connected directly to the pipes or mounted on a bracket.

First, prepare the connections to the PVB. They may have threads with Teflon tape or pipe dope for sealing. If there's tape, cut it with a razor blade or knife, making sure to remove any remnants. If there's pipe dope, you won't need to do anything additional, as it will be removed when you disconnect the pipes.

AD

Disconnecting the Inlet and Outlet Pipes

Using your adjustable wrenches, carefully loosen and remove the nuts that hold the inlet and outlet pipes to the PVB. You may need to use both wrenches, one to hold the pipe steady and the other to turn the nut. Be cautious not to overtighten, as this could strip the threads or damage the pipes.

Once you've removed the nuts, use another wrench to grasp the pipe and gently twist it to break the seal. It may take a few twists, and you might need a bit of leverage, but be patient and careful to avoid cracking or breaking the pipes. Have your bucket or towel ready to catch any remaining water.

Removing the Old PVB

After disconnecting both pipes, the PVB should be loose. If it's mounted on a bracket, unscrew it and remove it. If it's connected directly to the pipes, carefully twist and pull it off. If it's stuck, you may need to use a penetrating oil like WD-40 and wait a few minutes before retrying.

AD

If your PVB is old or severely damaged, you might need to cut it off using a hacksaw or pipe cutter. If you do this, make sure to deburr the pipes before connecting the new PVB to avoid creating a weak point that could leak or burst.

Installing the New Pressure Vacuum Breaker

With the old PVB removed, it's time to install the new one. The process is essentially the reverse of removing the old one, but with a few extra steps to ensure a proper seal and secure connection.

Before installing the new PVB, clean the threads of both the pipe and the PVB using a rag or brush. This is to ensure a tight seal and prevent leaks. If your new PVB doesn't come with new nuts, use the old ones, making sure they're not damaged or worn.

Connecting the New Pressure Vacuum Breaker

Place the new PVB in position, ensuring the inlet and outlet are correctly oriented. For the threaded connection, wrap the threads with Teflon tape, starting at the back of the thread and wrapping clockwise, making 3 to 4 stables of even, overlapping turns. If you're not using tape, apply a generous amount of pipe dope to the threads.

Hold the PVB in place with one wrench and use another wrench to secure it to the pipe by tightening the connection. Tighten as much as you can by hand first, then use the wrench to make sure it's tight. Be careful not to overtighten, as this could cause the threads to strip or the pipe to crack.

Repeat this process for the other pipe, ensuring both connections are tight and secure.

Testing and Securing the New PVB

Once both connections are made, turn on the water supply and check for leaks. If there are any, you may need to tighten the connections or apply more Teflon tape or pipe dope. If the connections don't leak, you're golden!

Finally, if your new PVB is mounted on a bracket, secure it with screws or bolts, ensuring it's firm and won't move. If it's connected directly to the pipes, it should be secure enough. Replace any insulation or wall material you cut away, ensuring the PVB remains accessible for future maintenance.

And there you have it - you've successfully replaced your old pressure vacuum breaker with a new one, ensuring your plumbing system remains safe and efficient. Regularly inspecting and maintaining your PVB will help prevent future issues. However, if you're unsure about any part of the process or if you encounter problems, don't hesitate to call a professional plumber. They can provide expert advice and ensure the job is done right. Happy DIYing!

AD