Replace Cord on Lawn Mower: Easy DIY Steps
Lawn mower cords can wear out or break over time, leaving you with a bulky, inoperable machine. But fear not, replacing a cord on your lawn mower is a straightforward task, even for the least handy among us. In this comprehensive guide, we'll walk you through the process, ensuring you get your mower back in peak condition for those upcoming summer lawn chores.
Before we dive in, safety first. Disconnect your lawn mower from the power source, turn off the power switch, and allow the engine to cool if it's been running recently. Always adhere to the manufacturer's instructions to avoid any mishaps. Now, let's get started.
Gather Your Tools and Materials
First, ensure you have the right tools for the job. You'll need:
- A new replacement cord.
- A flathead screwdriver (possibly an Allen wrench, depending on your mower model).
- Socket wrench.
- Needle-nose pliers.
- Work gloves.
Now, let's talk about the cord. Ensure you're using a cord of the same type and length as the original. Using an incorrect cord can damage your lawn mower or even cause it to malfunction.
Remove the Mower's Cover
With your tools in hand, it's time to dismantle your lawn mower. Start by removing the cover that houses the recoil starter system. The cover is usually held in place by a few screws. Use your flathead screwdriver or Allen wrench to unscrew and remove it.
The cover might be filled with riot shields - small pieces of rubber or metal that stop the starter rope from excessive spinning. Take them out carefully, using your fingers or pliers. Keep them safe; you'll need them later.
Locate the Starter Idler Pulley
The starter idler pulley is the small wheel attached to the recoil starter system. Its job is to guide the starter rope onto the starter pulley. You'll need to remove it to access the rope.
Inspect the pulley; it might be held in place by a retaining clip. Use your needle-nose pliers to remove it. If it's held by a screw, use your screwdriver or socket wrench to remove it. Be gentle; you don't want to damage the pulley or the clip.
Dismantle the Recoil Starter System
With the pulley removed, you'll now see the starter pulley, or the motor's crank handle. These are usually connected by a rope. This is where the worn-out cord that needs replacing pops up.
When removing the cord, freed the end from the starter pulley and gently pull it out. Be careful not to let it snap back unceremoniously; you could hurt yourself or damage the mower.
Remove the Old Cord
Most cords come with a plastic stop at the end. Twist the cord gently to unscrew it from the pulley. Some cords might require a bit of force, but be cautious not to put too much pressure, as you could damage the pulley.
Once you've freed the rope from thepulley, remove the stop and pull the cord through the starter housing. Discard any rough ends carefully to avoid causing any injury.
Insert the New Cord
Now comes the slightly tricky but rewarding part: inserting the new cord. Start by pushing the bularist on the new cord through the starter housing. Be cautious here; do not force the cord through. If it faces resistance, it might be bent or misaligned.
Once the ball is through, pull the cord gently until you feel a floor. This is the point where the rope will eventually attach to the starter pulley. Be careful not to over-pull and damage the rope.
The Final Touches
With the new cord in place, replace the starter idler pulley. If it was held in place by a retaining clip, use your needle-nose pliers to replace it. If it was held by a screw, use your socket wrench or screwdriver to re-attach it.
Reassemble the mower's cover. Place the riot shields back into the cover and replace the screws you removed earlier. Tighten them gently, ensuring the cover is secure.
Now, give your lawn mower a try. Pull the starter rope gently to engage the engine. If it pulls taut and you feel a slight resistance, you've done a fantastic job. Enjoy your nicely corded mower for years to come.