how to replace bathroom faucet drain

Mastering the Exchange: Replace Your Bathroom Faucet Drain

By Robert Wilson
AD

Are you tired of a slow draining bathroom sink or bathtub? The issue might be a clogged drain, which can be resolved by replacing the faucet drain. This task may seem daunting, but with the right tools and a bit of patience, you can tackle it like a pro. This guide will walk you through the process, from gathering tools to the final flush.

Before you start, ensure you have all the necessary tools and materials. This project typically requires a Phillips screwdriver, an adjustable wrench, a flathead screwdriver, a Allen wrench, a putty knife, and pliers. You'll also need a new pop-up drain assembly, which includes the drain stopper, linkage, and the lift rod. Now, let's dive into the step-by-step process.

Preparation and Removing the Old Drain

Start by turning off the water supply to your sink or bathtub. Locate the supply tubes, usually behind the fixture or under the sink, and turn the shutoff valve clockwise to close it. Open the faucet to release any residual water pressure.

AD
how to replace a sink drain in a bathroom with pictures and text overlays
how to replace a sink drain in a bathroom with pictures and text overlays
How to Remove a Bathroom Sink Drain Step by Step
How to Remove a Bathroom Sink Drain Step by Step
Bathroom Faucet Replacement For Beginners - Making Manzanita
Bathroom Faucet Replacement For Beginners - Making Manzanita

Next, remove the old drain. Begin by unscrewing the nuts that secure the tailpiece (the horizontal pipe connecting the faucet to the drain) to the wall or cabinet. Use an adjustable wrench to Loosen the lock nut at the base of the faucet and lift the drain stopper off its lever arm.

Disconnecting the Drain Assembly

Using an Allen wrench, remove the set screw that holds the lift rod to the drain body. Carefully lift the lift rod out of the drain body. You may need to wiggle it a bit to free it. Now, with the drain body disconnected from the lift rod, you can remove the old drain. If it's stuck, try using a flathead screwdriver or a pair of pliers to gently pry it off.

How to Replace a Bathroom Faucet & Drain | Bathroom Renovation
How to Replace a Bathroom Faucet & Drain | Bathroom Renovation
a person fixing a faucet in a sink
a person fixing a faucet in a sink

If your drain has been in place for a while, you might find that the plumber's putty or silicone sealant used to secure it has hardened. Use a putty knife to carefully scrape off any remaining residue. Be sure to wear gloves and eye protection during this step.

Preparing the New Drain

Unpack your new pop-up drain assembly and ensure it's the right fit for your faucet. The new drain should come with a rubber gasket. If not, you may need to purchase one separately. Apply a thin layer of plumber's putty around the bottom of the drain, just inside the threads. This will create a watertight seal.

AD

Thread the new drain into place, sandwiching the gasket between the drain and the surface of your sink or bathtub. Hand-tighten the drain until the putty begins to squeeze out. Remove any excess putty with a knife, being careful not to damage the gasket.

Connecting the New Drain Assembly

Reattach the lift rod to the new drain body using the set screw and Allen wrench. Ensure the rod is properly secured and aligns with the lever arm. Reinstall the lock nut at the base of the faucet and secure it with the adjustable wrench.

If you have a center-set or single-handle faucet, you'll need to reattach the lift rod to the faucet parts. Consult your faucet's installation instructions for specific steps.

AD

Reconnecting the Water Supply

With the new drain and assembly in place, it's time to reconnect the water supply. Turn the shutoff valve counterclockwise to open it. Turn on the faucet to test the new drain and ensure there are no leaks. If water is dripping from around the drain body, you may need to reapply plumber's putty and tighten the drain further.

Once you're satisfied that the drain and assembly are secure and leak-free, flush the system by running a few gallons of water through the faucet. This will help clear any remaining debris and ensure a smooth drain.

Finishing Touches

If you had to remove any cabinet doors or access panels during this process, remember to put them back in place. Clean up any tools you used and dispose of any old hardware or putty responsibly.

AD

There you have it! With just a bit of DIY know-how and the right tools, you've successfully replaced your bathroom faucet drain. You've not only improved the functionality of your sink or bathtub but also added a fresh touch to your bathroom. Enjoy your smooth-draining fixtures and happy DIY-ing!

AD