Step-by-Step Guide: Replace Electric Water Heater Element
Is your electric water heater not performing as well as it used to? Don't let cold showers dampen your spirits. Replacing an electric water heater element is a task you can tackle yourself, saving you a significant amount of money. Here's a comprehensive guide to walk you through the process.
Before you start, make sure you have the right tools and equipment. You'll need a voltage tester, screwdriver, pliers, adjustable wrench, and a new water heater element. It's also a good idea to have a bucket nearby to catch any water that may leak out.
Safety Measures Before You Begin
Safety should always be your top priority when working with electrical appliances.
1. **Turn Off Power and Water:** Start by turning off the power to your water heater at the circuit breaker. Then, turn off the water supply to your heater at the cold water shut-off valve.
Test the Heater Element
Before you start disassembling, it's a good idea to test the element to ensure it's the problem. Use your voltage tester to do this.
1. Set your tester to the lowest setting (around 200 ohms for most testers). 2. Touch one probe to the element's voltage wire and the other to a grounded metal part of the heater. 3. If your tester beeps or lights up, the element is working. If not, it's likely your problem.
Locate and Remove the Access Panel
To replace the element, you'll need to access the inside of the heater.
1. The access panel is usually located on the side of the heater. It may be held in place with screws or a clip. 2. Once you've identified it, remove the panel using your screwdriver or your hands if it's a clip.
Remove the Old Element
With the access panel removed, you can now see and access the old element.
1. **Drain the Water:** Before removing the element, you'll need to drain some water from the tank. Open the drain valve at the bottom of the tank and allow some water to escape into your bucket.
Disconnect the Wires
Before you can remove the element, you'll need to disconnect the wires.
1. Use your voltage tester to ensure the wires are no longer hot. Then, carefully pull apart the wire connectors using your needle-nose pliers.
Remove the Old Element
Now you're ready to remove the old element.
1. Use your adjustable wrench to loosen and unscrew the mounting nuts that hold the element in place. 2. Once the nuts are loose, you can pull the old element out of the tank.
Install the New Element
With the old element out, it's time to install the new one.
1. **Wash the Area:** Before installing the new element, clean the area to remove any debris or rust. This will ensure a good connection for the new element.
Insert the New Element
Now you can insert the new element into the mounting hole. The threaded part of the element should go through the tank wall.
1. Once the element is in place, thread the mounting nuts back onto the element and finger-tighten them. 2. Then, use your wrench to tighten the nuts. Be careful not to overtighten as this could strip the threads or cause the element to leak.
Reconnect the Wires
Now you can reconnect the wires to the new element.
1. First, ensure the wires are still dry and free of any debris. If not, clean them gently with a damp cloth. 2. Then, connect the wires back to the new element, ensuring they're securely attached. If you're unsure about the polarity, consult your heater's manual or mark the wires before disconnecting them.
The Final Touches
With the new element installed and the wires reconnected, you're almost done.
1. **Replace the Access Panel:** Put the access panel back in place and secure it. Whether it's screwing it back on or clicking it into place, make sure it's secure.
Refill the Tank
Now it's time to refill the tank with water.
1. Turn the water supply valve back on and allow the tank to fill up. You should see water flowing into the tank via the cold water pipe. 2. Once the tank is full, you can turn the power back on at the circuit breaker.
There you have it! Your electric water heater is as good as new. Regular maintenance can help extend the life of your heater and prevent future issues. Always remember, safety first when dealing with electrical appliances. If at any point you feel unsure, don't hesitate to call a professional. Happy fixing!