how to replace a leaking spigot

How to Fix a Leaking Spigot: Step-by-Step Guide

By Thomas Lopez
AD

Are you tired of that persistent drip, drip, drip from your spigot? It's not only annoying but also a sign that you have a leaking spigot, which can lead to increased water bills and potential water damage. The good news is, replacing a leaking spigot is a DIY project that can save you money and time. In this comprehensive guide, we'll walk you through the process, step by step. Let's dive in.

Before we start, ensure you have the correct tools and materials. You'll need a Phillips and a flathead screwdriver, channel locks or adjustable pliers, a replacement spigot, Teflon tape, and a wrench. Having these ready will make the process smoother.

Inspecting and Preparing Your Spigot

A thorough inspection is crucial before you start. Turn off the water supply to your spigot. This is usually done at the main water supply valve. After that, open the spigot to drain any remaining water in the pipe. This will prevent any water from leaking while you're working.

AD
an old spigot with the words how to replace spigot on it
an old spigot with the words how to replace spigot on it
💧Fix Your Leaky Spigot with Our DIY Guide!
💧Fix Your Leaky Spigot with Our DIY Guide!
How to Replace an Outdoor Water Spigot
How to Replace an Outdoor Water Spigot

Now, let's talk about safety. Water behind a leaking spigot can be under high pressure, so be careful when removing the spigot. It's a good idea to wear safety glasses to protect your eyes from any debris or water that might spray out.

Removing the Old Spigot

Start by disconnecting the water hose, if any, from the spigot. Next, locate the set screw at the base of the spigot. Using a Phillips screwdriver, loosen and remove it. This will allow you to pull the handle off.

How To Replace a Leaking Outside Faucet In 5 Minutes - Garden Faucet / Hose Spigot
How To Replace a Leaking Outside Faucet In 5 Minutes - Garden Faucet / Hose Spigot
How to Replace an Outdoor Water Spigot
How to Replace an Outdoor Water Spigot

With the handle off, use a flathead screwdriver to pry off the escutcheon, the decorative cap that covers the spigot's mechanical parts. You might need to use some force, but be careful not to damage it. It can be reused.

Exposing the Stem and Packing Nut

The stem is the part of the spigot that moves up and down when you operate the handle. The packing nut is a threaded nut that holds the stem in place. Remove the packing nut using channel locks or adjustable pliers. You might need to hold the body of the spigot with a wrench to keep it steady while you're doing this.

AD

Once the packing nut is off, you should be able to pull out the stem. If it's stuck, you can use a hammer and a piece of wood to gently tap it out. Always protect the spigot body with a cloth to avoid scratching or damaging it.

Preparing the New Spigot

Before installing the new spigot, make sure it's the right one for your needs. Spigots come in different shapes, sizes, and materials, so ensure you get a compatible one.

Now, let's prepare the new spigot for installation. Wrap the threads of the new spigot with Teflon tape. This helps create a watertight seal and prevents leaks. Apply the tape in a clockwise direction, overlapping each layer by half. Be careful not to use too much tape, as this can cause the spigot to jam.

AD

Installing the New Spigot

Start by inserting the spout of the new spigot into the hole in the wall. Make sure it's flush with the wall surface. Then, apply a small amount of plumber's putty around the base of the spigot to create a tight seal.

Now, thread the spigot into the hole. Be careful not to cross-thread it. Use your hand to start the thread, then use a wrench to tighten it. Tighten it just until it's snug, then back it out slightly. This ensures a good seal without overtightening and cracking the spigot.

Assembling the Remaining Parts

Now that the spigot is installed, it's time to reassemble the rest of the parts. Replace the packing nut and stem. You might need to wrap some plumber's putty or Teflon tape around the stem to create a good seal.

AD

Push the stem back into the spigot body and thread the packing nut back onto the stem. Use channel locks or adjustable pliers to tighten it. Again, be careful not to overtighten.

Testing the New Spigot

Before turning the water supply back on, perform a test run of your new spigot. Close the spigot handle and turn the water supply back on. This allows you to check for any leaks before water is under pressure.

After you've confirmed there are no leaks, open the spigot handle to drain the water in the pipe. Then, close the spigot and turn the water supply off again. This will release any remaining air in the pipe. Turn the water supply back on, open the spigot, and check for any leaks. If there are no leaks, your new spigot is installed correctly.

And there you have it! You've successfully replaced a leaking spigot. If you've followed these steps correctly, you should have a reliable, drip-free spigot for years to come. Regular maintenance, like checking for leaks and tightening connections, will ensure its longevity. Happy DIYing!

AD