Step-by-Step: How to Replace a Drag Link on a Craftsman Lawn Mower
Nothing turns a well-manicured lawn into an eyesore faster than clunky steering on your trusty Craftsman lawn mower. One of the most common culprits behind this issue is a worn-out drag link. Replacing this component isn't as daunting as it sounds. With the right tools and a little patience, you can get your mower moving smoothly again in no time. Here's a step-by-step guide on how to replace a drag link on a Craftsman lawn mower.
Before we dive in, remember that lawn mower maintenance is a task best done during the off-season. The below guide assumes your mower is clean, cool, and unused for several hours. Always ensure your safety by disconnecting the ignition wire and letting the engine cool before you start tinkering.
Gather Your Tools and Materials
First things first, you'll need the right tools to get the job done safely and accurately. Here's what you'll need:
- New Drag Link: Ensure you've got the correct part number for your Craftsman model.
- Socket Wrench Set: You'll need metric sockets ranging from 10mm to 17mm.
- Open-Ended Wrench: A 12mm wrench is essential for removing the bell crank nut.
- Pliers or Channellock Pliers: These help to bend the cotter pin and remove it from the steering rod.
- Wire Cutters: To snip off the old cotter pin.
- Grease: With the correct API GL-4 grade to lubricate the new drag link.
- Shop Towels or Rags: For cleanup and applying grease.
Disconnect the Mower Deck
To access the drag link, you'll need to disconnect the mower deck. Here's how:
- Tip the mower upright so you can access the underside.
- Locate the two connection points where the mower deck attaches to the frame.
- Remove the cotter pin and washer using pliers or channellock pliers and a hammer. You might need to use a punch to drive the cotter pin out if it's stuck.
- Unscrew and remove the nut using your 12mm wrench.
- Slide the mower deck off the support tube.
Remove the Old Drag Link
Now that the mower deck is disconnected, it's time to remove the old drag link.
- Locate the bell crank and steering rod connecting to the left RearWheel Transaction Axle (RTT).
- Identify the drag link connecting the bell crank and the RTT.
- Remove the cotter pin and washer from the drag link using pliers or channellock pliers and a hammer.
- Remove the nut securing the drag link to the RTT's clevis pin using a 17mm socket wrench.
- Disconnect the drag link by pulling it away from the RTT.
- Using a 14mm socket wrench, unbolt the drag link from the bell crank lever. You may need to use a breaker bar for extra leverage.
- Slide the old drag link off the bell crank lever.
Install the New Drag Link
With the old drag link gone, it's time to install the new one.
Inspect the new drag link before installation to ensure all parts are present and in good working order. Also, grease both ends of the new drag link using API GL-4 grade grease.
Connect the Drag Link to the Bell Crank Lever
Begin installing the new drag link by connecting it to the bell crank lever.
- Slide the drag link onto the bell crank lever.
- Secure it in place using the 14mm nut and a new cotter pin.
Connect the Drag Link to the RTT
Now, connect the other end of the drag link to the RTT.
- Position the drag link in the RTT's clevis pin and slide it in place.
- Secure it with the 17mm nut and a new cotter pin.
Reassemble the Mower Deck
With the new drag link installed, it's time to reconnect the mower deck.
Simply reverse the process you used to disconnect the mower deck earlier:
- Slide the mower deck onto the support tube.
- Secure it with the 12mm nut and a new cotter pin with washer.
- Lower the mower to the ground.
Before you take your Craftsman lawn mower for a spin, ensure all nuts are tight and cotter pins are properly secured. Regularly inspect your drag link and keep it lubricated to extend its lifespan and prevent future breakdowns. Happy mowing!