how to clean craftsman lawn mower carburetor

Clean Craftsman Lawn Mower Carburetor: Step-By-Step Guide

By Nicole Thomas
AD

Keeping your Craftsman lawn mower in tiptop shape requires regular maintenance, and cleaning the carburetor is a crucial task. A clogged or dirty carburetor can cause your mower to run poorly, lose power, or even not start at all. With a bit of know-how and the right tools, you can easily clean your Craftsman lawn mower carburetor and ensure optimal performance.

Before you dive in, gather your tools: a socket or wrench set, carburetor cleaner, a shop rag, a flathead screwdriver, and a small paintbrush. You'll also need new gaskets and a new air filter, as these are often changed during a carburetor cleaning. Let's get started!

Preparation and Disassembly

First, ensure your mower is cold and on a level surface to prevent fuel spills. Position a tray underneath the carburetor to catch any stray fuel.

AD
a lawn mower with the words how to clean lawn mower carburetor without removing it
a lawn mower with the words how to clean lawn mower carburetor without removing it
How to Use Lawn Mower Carburetor Cleaner
How to Use Lawn Mower Carburetor Cleaner
Carburetor Repair, Maintenance & Adjustment How-To Guide
Carburetor Repair, Maintenance & Adjustment How-To Guide

Locate the air filter and remove its cover. Remove the air filter itself and set it aside. You'll clean this later. Now, find the bolts holding the carburetor in place and use your wrench to remove them. You might need a socket set for some Craftsman models. Support the carburetor as you remove the bolts to prevent it from falling.

Disconnect and Remove the Carburetor

Once the bolts are out, disconnect the fuel line at the carburetor. Some models might have a small screw to loosen before you can pull the line off. Also, remove the choke and throttle cables by gently sliding them out of their spots. Be cautious not to damage or bend them.

How to Clean a Lawn Mower Carburetor (Step By Step Guide)
How to Clean a Lawn Mower Carburetor (Step By Step Guide)
How to Clean Riding Mower Carburetor (Fix Hard Starts Fast)
How to Clean Riding Mower Carburetor (Fix Hard Starts Fast)

With everything disconnected, carefully remove the carburetor. You might need to wiggle it a bit to free it from the gasket. Once off, set it on your workbench, ensuring the float and needle are still intact. Now, it's time to disassemble the carburetor itself.

Disassemble the Carburetor

Start by removing the large nut on the bottom of the carburetor, using a wrench if necessary. This nut secures the float bowl, which you can now remove. Inside, you'll find a float, a pin, and a brass jet. Remove the pin and jet, being careful not to lose the small spring underneath.

AD

Next, remove the top of the carburetor. On some models, you'll need a flathead screwdriver to pry off the brass fittings. With the top off, you'll see the main jet and the needle. Remove the needle and seat, and set them aside with their respective springs.

Cleaning the Carburetor

Now that your carburetor is disassembled, it's time to clean it. Inspect each part for signs of wear or damage. Replace any parts that don't look right.

Cleaning the Jets and Needle

Use your carburetor cleaner to thoroughly clean the main and brass jets, the needle, and the seat. You can use a small paintbrush to apply the cleaner and scrub gently. Ensure no debris or old fuel remains. Avoid using wire brushes, as they can damage the jets.

AD

After cleaning, dry each part with a shop rag. Ensure they're completely dry before reassembly, as any remaining moisture can cause new issues.

Cleaning the Float and Bowl

Clean the float and float bowl using your carburetor cleaner and a shop rag. Ensure no residue or old fuel remains. Check the float for proper operation by submerging it in fuel. It should rise and fall as expected. If not, you may need to replace it.

Clean the air filter in a separate container using your cleaner and a small brush. Rinse it with clean water, allow it to air dry completely, then check that it fits snugly in its cover.

AD

Reassembly and Reinstallation

Reassembly is the reverse of disassembly. Ensure you're reinstalling the parts in the correct order and that everything lines up as it should.

Reassemble the Carburetor

Start by reinstalling the float and its mechanism, ensuring the float hinges properly. Reinstall the brass jet and its spring, followed by the main jet and needle, along with their respective springs. Ensure the needle slides smoothly in the main jet.

Reattach the top of the carburetor, securing it firmly but not overly tight. Reinstall the float bowl, securing it with the large nut. Ensure all parts are snug but not overly tight to prevent cracking or breaking.

Reinstall the Carburetor

Before reinstallation, replace the gaskets on the carburetor and the engine. Reinstall the carburetor on the engine, ensuring it's correctly positioned and sealed. Secure it with the bolts you removed earlier.

Reconnect the fuel line, choke, and throttle cables. Ensure they're securely attached and functioning correctly. Replace the air filter and its cover.

After reassembly, start the engine and let it run for a few minutes to work out any remaining cleaner. Check for any leaks, and ensure the mower is running correctly. Happy mowing!

AD