how to remove tub cartridge

-how-to-remove-tub-cartridge

By Ashley Thompson
AD

Is your faucet's handle unreliable or saying "тub faucet?" It might be time to replace the worn-out cartridge. Removing a tub cartridge can seem intimidating, but with the right tools and steps, it's a manageable DIY task. Let's dive into a comprehensive guide on how to remove a tub cartridge. Remember, safety first: always turn off the water main before starting any plumbing work.

Before we begin, gather your tools: an adjustable wrench, a flathead screwdriver, a cartridge puller (often included with new cartridges), and penetrating oil (like WD-40). Let's get started!

Preparation and Accessing the Cartridge

Begin by turning off both the cold and hot water supply valves under your sink. Then, turn on the faucet to relieve any remaining water pressure. Next, locate the set screw at the base of the faucet handle. This screw secures the handle in place and needs to be removed before you can access the cartridge.

AD
How to Remove a Leaky Shower Valve Cartridge - HandyManHowTo
How to Remove a Leaky Shower Valve Cartridge - HandyManHowTo
a person is using a screwdriver to fix a hole in the tile wall
a person is using a screwdriver to fix a hole in the tile wall
Replace Your Bathtub Drain
Replace Your Bathtub Drain

Using a flathead screwdriver, carefully unscrew and remove the set screw. Once the screw is out, your faucet handle should lift off, revealing the cartridge underneath.

Removing the Old Cartridge

You'll likely find a brass insert surrounding the cartridge. This insert helps anchor the cartridge and should be removed first. Grasp it with pliers and gently wiggle it back and forth to loosen it, then pull it straight out.

a person is fixing a bathtub in the bathroom with plumbing and accessories around it
a person is fixing a bathtub in the bathroom with plumbing and accessories around it
Your Guide to Replacing a Shower Cartridge - DIY Bathroom Improvement!
Your Guide to Replacing a Shower Cartridge - DIY Bathroom Improvement!

Using a Cartridge Puller

Insert the cartridge puller tool into the hole at the top of the cartridge.ிகளIn most cases, you can use the tool to just pull the cartridge straight out. However, if the cartridge is stuck, move on to the next step.

Apply some penetrating oil around the cartridge. Let it sit for about 15 minutes to help break down any rust or mineral buildup.

AD

Removing a Stubborn Cartridge

If the cartridge is still not budging, try gently tapping it with a soft mallet or hammer. This can help break the seal between the cartridge and the faucet. Be careful not to Damage the cartridge or the faucet.

After tapping, try pulling the cartridge out again. It should now come out with a little bit of effort. If not, you may need to consult a professional plumber.

Inspecting and Preparing for the New Cartridge

Once the old cartridge is out, take a moment to inspect the area for any corrosion or damage. If you find any issues, now is the time to address them before installing the new cartridge.

AD

Before installing the new cartridge, apply a light coat of plumber's grease to the O-rings. This will help ensure a proper seal and make removal easier in the future.

Installing the New Cartridge

Insert the new cartridge into the faucet body, ensuring it's properly aligned with the hot and cold water inlets. Gently push the cartridge in until it's fully seated.

Reinstall the brass insert and the faucet handle, securing the handle with the set screw you removed earlier. Then, slowly turn the water supply valves back on. Test the faucet handle to ensure it turns smoothly and the water runs as expected.

AD

Congratulations! You've successfully removed and replaced your tub cartridge. Regular maintenance can help prevent future issues, but if you're ever unsure about any step, don't hesitate to consult a professional. Happy plumbing!

AD