how to remove buffer tube

How to Remove Buffer Tube

By Robert Hernandez
AD

If you're a firearm enthusiast looking to customize your rifle, you might find yourself needing to remove the buffer tube at some point. This component is located at the rear of an AR-15 style rifle, and while it might seem daunting to remove it, this guide will walk you through the process step-by-step.

Before you start, ensure you have the right tools and a safe, well-lit workspace. You'll need a buffer wrench, a punch, and a hammer. Always remember to unload your firearm and check that there are no rounds left in the chamber or magazine. Safety first!

Understanding the Buffer Tube

The buffer tube houses the buffer and spring, which absorb recoil and help cycle the action. Removing it allows you to adjust the overall length of your rifle, swap out parts, or install accessories like stocks or braces.

AD
1.3M views · 6.8K reactions | How to remove a tube fitting easily! | Pixel Pop | Facebook
1.3M views · 6.8K reactions | How to remove a tube fitting easily! | Pixel Pop | Facebook
Retubing
Retubing
Elektor Tube Screamerish - AMZ-FX Guitar Effects Blog
Elektor Tube Screamerish - AMZ-FX Guitar Effects Blog

Before proceeding, familiarize yourself with the buffer tube's components. The castle nut threads onto the tube and secures it in place, while the end plate closes off the rear of the tube. The buffer and spring are housed inside, and the ejector and ejector spring fit into the receiver extension (buffer tube).

Preparation: Disassembly

Start by removing the lower receiver's rear takedown pin. Use a punch and a hammer to lightly tap the pin out from the left side. Next, pull the trigger group (including the trigger, hammer, and disconnector) out of the lower receiver.

HOW TO MAKE a REUSABLE Toothpaste Tube
HOW TO MAKE a REUSABLE Toothpaste Tube
Nasogatric Tube Removal.wmv
Nasogatric Tube Removal.wmv

Remove the buffer and spring assembly from the buffer tube. You can do this by pulling the tube and its contents out of the rear of the lower receiver. Be careful, as the buffer and spring are under significant tension and can cause minor injuries if they snap out suddenly.

Removing the Buffer Tube

With the buffer assembly removed, you're ready to tackle the buffer tube itself. Using a buffer wrench, thread the wrench onto the castle nut and turn it clockwise. This will loosen and remove the castle nut, allowing you to pull the buffer tube out of the receiver extension channel.

AD

If the tube is particularly tight, you might need to use a punch and hammer to tap it gently, forcing it to turn. Once the castle nut is removed, pull the buffer tube straight out of the lower receiver. Always ensure you're pulling in line with the receiver to prevent damage.

Inspecting and Planning Reassembly

Now that the buffer tube is removed, take a moment to inspect it and the inside of your lower receiver. You might notice some wear and tear, which is completely normal.

Before reassembly, decide whether you want to reinstall the original buffer tube or replace it with a new one. There are various buffer tubes on the market, offering different features and lengths. Consider your needs when making your decision.

AD

Preparation for Reassembly

If you're reinstalling the original buffer tube, ensure it's clean and free of any debris. If you're installing a new one, make sure it's compatible with your lower receiver and has the correct threading for the castle nut.

Assemble the buffer and spring, ejector, and ejector spring in the correct order. If you're unsure, consult your firearm's manual or contact the manufacturer for clarification.

Reinstalling the Buffer Tube

Start by threading the buffer tube into the receiver extension channel. Ensure it's aligned correctly to avoid cross-threading and potential damage. Once the tube is fully seated, use the buffer wrench to thread the castle nut onto the tube, turning it counter-clockwise until it's snug.

AD

Use a torque wrench to tighten the castle nut to the manufacturer's recommended specification. This is typically around 30-40 in-lbs of torque. Be careful not to overtighten, as this can strip the threads or cause other damage.

Reassemble the lower receiver, reinserting the buffer and spring assembly, the buffer tube, and finally, the trigger group. Replace the rear takedown pin and conduct a function test, ensuring everything moves smoothly and aligns correctly. Now that you've mastered the art of removing and reinstalling the buffer tube, enjoy your customized rifle!

AD