Fixing a Broken Tub Drain: How to Remove Crossbar
A broken crosshair in your tub drain can cause serious water backup and unsanitary conditions, making it crucial to remove it as soon as possible. While it might seem like a daunting task, removing a tub drain with broken crosshairs is absolutely achievable with the right tools and techniques. Let's dive into a comprehensive guide to help you tackle this common home improvement challenge.
Before we begin, safety should be your top priority. Ensure the area is well-lit, and wear appropriate protective gear, including old clothes, gloves, and safety goggles. Now, let's roll up our sleeves and get ready to remove that broken crosshair.
Understanding Your Tub Drain
Tub drains come in various types, but most share a common layout: the strainer, the crosshair, and the drain pipe. Familiarizing yourself with these components will help you better understand the process involved in removing the broken crosshair.
First, locate and identify the strainer – the flat, perforated metal disk that sits at the bottom of your tub. Next, find the crosshair, which is directly beneath the strainer and connects the two. Lastly, locate the drain pipe, which runs vertically through the floor of your tub and into your plumbing system.
Preparation: Gathering the Necessary Tools
Having the right tools at hand will make your repair job much easier. Here's a list of essential tools you'll need to remove a tub drain with broken crosshairs:
- Adjustable wrench
- Pipe wrench
- channel lock pliers
- Flathead and Phillips screwdrivers
- Hacksaw or utility knife
- Putty knife
- Tub and tile caulk
- Grout saw or oscillating tool (for tile surfaces)
Disassembling the Tub Drain
Now that you have your tools handy, it's time to start disassembling the tub drain. Begin by turning off the water supply to your tub at the main water shutoff valve. Then, follow these steps to remove the strainer and expose the crosshair:
1. Remove the drain plug (if present) using the appropriate screwdriver.
2. Use an adjustable wrench to loosen and remove the locknut that secures the strainer to the tub drain.
3. Carefully lift the strainer out of the tub, taking note of its orientation for easier reassembly later on.
Removing the Broken Crosshair
With the strainer removed, you'll now have direct access to the broken crosshair. Inspect it closely to assess the damage, and determine the best method for removal. In most cases, you can unscrew or pry it out, but sometimes more forceful methods may be necessary.
Unscrewing or Prying Out the Crosshair
If your crosshair is secured with screws, use a screwdriver to remove them and dislodge the crosshair. If it's held in place by friction or another type of hardware, try using channel lock pliers or a utility knife to carefully pry it out.
Using More Forceful Methods
Sometimes, broken crosshairs may be stubborn or completely deteriorated, making it difficult to remove them using conventional methods. In these cases, you may need to use a hacksaw to cut the crosshair into smaller pieces, or try using a grout saw or oscillating tool to grind it out. Be cautious while using these tools to prevent damaging the drain pipe.
Cleaning and Preparing the Drain Area
With the broken crosshair removed, it's essential to clean the drain area thoroughly to ensure a proper fit for the new crosshair. Use a putty knife to scrape away any old caulk or debris, and inspect the drain pipe for any signs of damage or corrosion.
Replacing the Drain Crosshair
Once the drain area is clean and dry, it's time to install the new crosshair. Ensure that the new crosshair is compatible with your tub drain and follows the same design as the original. To install the new crosshair:
1. Apply a small amount of tub and tile caulk around the drain opening to create a watertight seal.
2. Position the new crosshair in place, ensuring it's properly centered and fitted within the drain opening.
3. Secure the new crosshair using the appropriate hardware or by pressing it firmly into place, depending on the type of crosshair you're installing.
Reassembling the Tub Drain
With the new crosshair installed, you can now reassemble the tub drain by reversing the steps you took to disassemble it earlier. First, place the strainer back into the tub, ensuring it's properly aligned with the new crosshair. Then, secure it in place using the locknut and adjustable wrench. Lastly, reattach the drain plug using the appropriate screwdriver.
Before turning the water supply back on, inspect your work to ensure the tub drain is properly seated and there are no leaks. Once you're satisfied with the repair, carefully turn the water back on and test the drain. By following these comprehensive steps, you should now have successfully removed the broken crosshair and replaced it with a new one, restoring proper drainage to your tub.
Regular maintenance and inspections of your tub drain can help prevent future issues and extend the lifespan of your hardware. If you encounter any challenges during the repair process or suspect a more significant plumbing problem, don't hesitate to consult a professional plumber for expert assistance. Happy repair journey!