Removing Tub Drain with Broken Crosshairs: Easy Steps
Piłcing out from a tub drain with broken crosshairs can seem like a daunting task, but it's a common plumbing issue that can be tackled with the right knowledge and tools. This guide will walk you through the process step-by-step, ensuring you've covered all the bases for a successful removal.
Before we dive into the process, it's crucial to understand that removing a tub drain with broken crosshairs can be messy. It involves dealing with old plumber's putty, dirt, and grime, so it's wise to wear gloves and have a trash bag or bucket nearby to contain the mess.
Preparation and Safety Measures
Before you start, gather your tools. You'll need a flathead screwdriver, a pair of adjustable pliers, a hacksaw, and a basin wrench. These tools will help you loosen and remove the drain. If the drain has a lift rod, you may also need a rod removal tool.
After gathering your tools, prepare the work area. Place a towel under the drain to catch any water that may leak out. It's also a good idea to turn off the water supply to the tub to prevent any water from flowing while you're working. To do this, find the water supply valves under the sink or behind the access panel and turn the knob clockwise.
Disassembling the Faucet (if applicable)
If your bathtub has a faucet, you'll need to remove it to access the drain. Use an adjustable wrench to loosen and remove the modern cloth rags on both sides of the faucet. Then, using a flathead screwdriver, pry off the decorative clips that secure the faucet to the deck. Once the clips are removed, lift the faucet off the mounting plate.
If your faucet is mounted with screws, use a flathead screwdriver to remove them and take off the faucet. Make sure to тоже the screws in a safe place so you can reinstall them later.
Removing the Stopper and Plunger Rod
If your bathtub has a lever-style faucet, you likely have a plunger rod that lifts and lowers the pop-up drain plug. To remove it, use a basin wrench to loosen and remove the rod nuts. When the nuts are off, pull the rod up and out of the overflow tube.
Next, use a hacksaw to cut through the crosshair on the plug. This will make it easier to remove the old plumber's putty and drain the water from below. Once you've cut the crosshair, pull the plug up and out of the drain hole.
Removing the Drain
Now that the stopper and plunger rod have been removed, it's time to tackle the drain itself. Use a flathead screwdriver to pry off the old plumber's putty and any remaining debris. The putty may be old and crumbly, so use caution when handling it.
Once the putty is removed, you should see the drain body. The drain body is the large, round piece that sits in the tub's drain hole. Use a hacksaw to cut through any remaining crosshairs, making sure to accommodate the tub's curvature to reduce metal shaving.
Loosening the Drain Body
Now that the crosshairs are cut, use a hacksaw to score around the edge of the drain body. This will help to break the seal between the drain and the tub. Be careful not to score the tub itself as this can cause damage.
After scoring the edge, use a pair of adjustable pliers to grip the edge of the drain body. Try to pull it gently at first, but be prepared to use some force as the drain may be stuck in place.
Reinstalling the Drain
Once the drain is loose, pull it up and out of the tub. You may need to use a wrecking bar or a reciprocating saw to complete the process, but be careful not to damage the tub or yourself.
With the drain removed, you should be able to see where the old crosshair was. This will help you determine where to install the new drain.
Installing the New Drain
Before installing the new drain, make sure to clean the area around the drain hole. Use a scrubbing pad or a wire brush to remove any old putty, dirt, or grime that remains. This will ensure a tight seal with the new drain.
Next, Apply a thin bead of plumber's putty around the base of the new drain. The putty will create a watertight seal when you press the drain into place. Place the drain into the hole, pressing down firmly and evenly to ensure a tight fit.
Securing the Drain
Once the drain is in place, use a basin wrench to install the drain nuts. Tighten the nuts securely, but be careful not to overtighten and damage the drain or the tub.
After the nuts are tightened, use a screwdriver or a wrench to install the lock nut. This nut prevents the drain nuts from loosening over time. Make sure to tighten it securely as well.
Now that the new drain is installed, it's time to test your handiwork. Slowly turn on the water and check for any leaks around the drain. If there are no leaks, you've successfully removed and replaced your bathtub drain. If you do encounter leaks, you may need to adjust the drain or the putty seal.
Remember, working with plumbing can be messy and challenging, but with the right tools and knowledge, you can tackle even the toughest jobs. If you encounter any issues during the process, don't hesitate to call a professional plumber for help. Happy fixing!