how to remove a deadbolt lock without screws

Mastering the Lockpick: How to Remove a Deadbolt Lock Without Screws

By Ashley Rodriguez
AD

Accidents happen, and sometimes, a deadbolt lock can malfunction or break, leaving you with a lock that won't budge. If you find yourself in such a situation and the lock doesn't have visible screws, you might be wondering how to remove a deadbolt lock without screws. Fear not, as there are alternative methods to regain access to your door. This guide will walk you through the process, exploring why you might encounter a lock without screws and detailing the steps to remove it safely and effectively.

Deadbolt locks can be found without screws for a few reasons. Some high-security locks are designed this way to prevent tampering. Others might have been installed using a different method, such as drilling or using hidden mounting points. Regardless of the reason, removing a deadbolt lock without screws requires a different approach than simply unscrewing the lock. Let's dive into the two main methods: using a drill and the tabs removal method.

Drilling Out the Lock

The first method involves drilling through the lock cylinder to gain access to the internal components. This approach is best suited for when you need to remove the lock as soon as possible, but it should be used sparingly as it can damage the lock and door. Here's how to drill out a deadbolt lock without screws:

AD
How to Drill Out a Lock, Even If You've Never Done It Before
How to Drill Out a Lock, Even If You've Never Done It Before
How to Remove Deadbolt With No Screws - Where are the Deadbolt Screws?
How to Remove Deadbolt With No Screws - Where are the Deadbolt Screws?
How to Install a Deadbolt Lock
How to Install a Deadbolt Lock

Safety first: Put on safety glasses and wear ear protection if you have it. Drilling can create debris and noise, so it's crucial to protect yourself. Choose a drill bit slightly smaller than the diameter of the lock cylinder, typically a 7/32" bit for most residential locks.

Drilling the Lock Cylinder

Mark the center of the lock cylinder using a pencil. Apply gentle pressure to the drill and slowly drill into the lock. Be cautious not to apply too much pressure, as this could cause the drill to bind or break. Drill at a steady pace, monitoring the progress until you've gone through the entire cylinder.

How To Remove A Deadbolt Lock Without Screws - Hunker
How To Remove A Deadbolt Lock Without Screws - Hunker
How to replace a deadbolt door lock in 10 minutes. Easy install!
How to replace a deadbolt door lock in 10 minutes. Easy install!

Once the cylinder is completely drilled out, you should be able to remove the lock from the door. You might need to use pliers or a flathead screwdriver to gently pry the lock out, depending on the design of the lock and door.

Removing the Lock from the Door

If the lock is still stubbornly lodged in the door, try wiggling it back and forth to disengage the latch. You may need to use a hammer and a screwdriver to gently tap the lock loose, taking care not to damage the door. Once the lock is free, you can remove it completely and install a new one if needed.

AD

The Tabs Removal Method

The tabs removal method is a non-destructive technique that works for some lock models without screws. This method involves removing small tabs or clips that secure the lock to the door, allowing you to disassemble the lock without damaging it. Follow these steps to attempt tabs removal:

1. Locate the tabs: Inspect the edge of the lock cylinder, installation plate, or the side of the lock mechanism. Look for small tabs, clips, or snap rings that may be securing the lock in place. A small inspection hole or a tiny gap might reveal the location of these tabs.

2. Determine if tabs are present: If you can't see any tabs, the lock might not have them, or they might be hidden deep within the mechanism. In this case, proceed with caution, as drilling might be necessary. Otherwise, continue with the tabs removal process.

AD

Removing the Tabs

Using a small, precision tool like a dental pick or a narrow flathead screwdriver, carefully insert it into the gap or hole where the tabs are located. Gently pry the tabs out, one at a time. Applying steady, gentle pressure is crucial to prevent damaging the tabs or the lock.

It might take a bit of finesse and patience to remove all the tabs. Once you've removed all of them, the lock should be loose enough to be gently pried out of the door. If the lock is still not coming out, there might be additional tabs or configured screws hidden within the mechanism.

Once the lock is removed, you can inspect the internal components for any additional tabs or screws. If present, carefully remove them using the same technique. With all the tabs and screws removed, the lock should now come out easily.

AD

In case you couldn't remove the lock using the tabs removal method, don't hesitate to seek professional help. A qualified locksmith can assist you with removing the lock safely and reinstalling a new one if needed.

Removing a deadbolt lock without screws can be a challenging task, but with the right approach and a bit of patience, you can regain access to your door. always prioritize safety, and don't hesitate to consult a professional if you encounter any issues. Now that you've successfully removed the lock, it's time to consider upgrading to a new, reliable lock for added security.

AD