how to remove a cigarette lighter socket

How to Remove a Cigarette Lighter Socket

By Robert Lopez
AD

Ever faced a burnt cigarette in your car lighter socket? Or perhaps you're just looking to replace it with a USB adapter? Removing a cigarette lighter socket might seem daunting at first, but it's simpler than you think. This step-by-step guide will walk you through the process, ensuring you get it right.

Before you start, gather your tools: a flathead screwdriver, a pair of pliers, and a new lighter socket or USB adapter if you're replacing it. Safety first, so ensure your car is off, the keys are out of the ignition, and the parking brake is engaged.

Disconnecting the Wiring

The first step is to disconnect the wiring connected to the cigarette lighter socket. This will allow you to remove the socket safely.

AD
How to Replace a 12v Cigarette Lighter Socket With a USB Charger Port and Voltmeter
How to Replace a 12v Cigarette Lighter Socket With a USB Charger Port and Voltmeter
Car charger not working FIX Cigarette lighter socket repair auxiliary power outlet fuse replacement
Car charger not working FIX Cigarette lighter socket repair auxiliary power outlet fuse replacement
HOW TO REPLACE CAR CIGARETTE LIGHTER (12V) QUICK AND EASY IN ANY CAR 2018
HOW TO REPLACE CAR CIGARETTE LIGHTER (12V) QUICK AND EASY IN ANY CAR 2018

Look under your car's dashboard for a panel that the lighter socket passes through. This panel should have screws that you can remove using your flathead screwdriver. Once you've removed the screws, carefully pry off the panel to expose the wiring.

Locating the Wiring

Now that you have access to the wiring, locate the two wires connected to the back of the lighter socket. These will be positive and negative wires. The positive wire, usually red, should be connected to a screw at the back of the socket. The negative wire, usually black, will be connected to a metal chunk inside the socket.

INSTALL: Cigarette Lighter Replacement | 2002-2007 Subaru Impreza, WRX, & STi
INSTALL: Cigarette Lighter Replacement | 2002-2007 Subaru Impreza, WRX, & STi

You might need to pull the wiring harness gently to expose the screws. Be careful not to damage any of the wires or their insulation.

Removing the Wires

Using your pliers, carefully grip each wire's connectors and twist them counterclockwise. This should loosen and eventually disconnect the wires from the socket. If your car uses push-in connectors, you might need to press down and pull out the wires.

AD

After disconnecting both wires, the cigarette lighter socket should be free from the wiring harness.

Removing the Lighter Socket

Now that the lighter socket is disconnected from the wiring, it's time to remove it from the dash panel.

There should be retention clips holding the socket in place. These are usually located on the sides or at the back of the socket. You can carefully pry these clips open using your flathead screwdriver or a butter knife. Be gentle to avoid damaging the clips or the socket.

AD

Prying the Socket

With the retention clips loosened, carefully insert the screwdriver or knife behind the socket and gently pry it out. Be cautious not to damage the socket, especially if you're replacing it with a similar one.

If you're having trouble, you can try pulling the socket gently while wiggling it side to side. This should help it pop out of the dash panel.

Installing the New Socket or USB Adapter

With the old socket out, you can now insert your new cigarette lighter socket or USB adapter. Make sure it's correctly aligned with the hole in the dash panel.

AD

Remember to follow the manufacturer's instructions if you're installing a new socket with different retention clips. Push the new socket or adapter into the dash panel until it's firmly seated and the retention clips click into place.

Reconnecting the Wiring

Now that your new socket or adapter is in place, it's time to reconnect the wiring.

Insert the socket or adapter's wires back into the wiring harness, ensuring they're fully pushed in and secure. Then, tuck the wiring back into the dash and carefully replace the panel you removed earlier. Screw it back into place.

Testing the New Socket or Adapter

Before you put everything back in its place, start your car and test your new cigarette lighter socket or USB adapter. Insert a cigarette lighter plug or USB device and ensure it's working properly.

If everything works as expected, turn off your car and replace the dashboard panels you removed. Now, you can enjoy your new cigarette lighter socket or USB adapter.

Congratulations, you've successfully removed and replaced your car's cigarette lighter socket! Remember, always prioritize safety when working on your car. If you're unsure about any step, don't hesitate to consult a professional or refer to your vehicle's owner's manual. Safe driving!

AD