how to install whirlpool water filter

Step-by-Step Guide: How to Install Whirlpool Water Filter

By Daniel Davis
AD

Looking to improve the water quality in your Whirlpool refrigerator or refrigerator/freezer? Installing a Whirlpool water filter is a simple and effective solution. Not only does it provide you with fresh, clean water, but it also keeps your appliance's dispenser and ice maker working efficiently. Here's a comprehensive, step-by-step guide on how to install a Whirlpool water filter.

Before we start, ensure you have the right Whirlpool water filter for your appliance. Whirlpool offers a range of filters, including the WHFE14F, WHFE1, and WH1ATF models. Consult your owner's manual or use Whirlpool's model finder tool to confirm your filter model.

Preparing for Installation

Before you begin, gather the necessary tools and parts. You'll need a new Whirlpool water filter, a screwdriver (usually a Phillips #1), and some patience. It's also a good idea to have a towel or bowl ready to catch any water that may dispense during the process.

AD
a person is holding an electric toothbrush in front of a water filter
a person is holding an electric toothbrush in front of a water filter
How To Change Ice Maker Filter On Whirlpool – Storables
How To Change Ice Maker Filter On Whirlpool – Storables
How to Install a Water Softener | Whirlpool
How to Install a Water Softener | Whirlpool

Next, locate the filter in your appliance. For refrigerators, it's typically found in the grille at the bottom or behind the lower-left corner panel. For refrigerator/freezers, it's usually behind the lower-right corner panel or on the floor of the fresh food compartment.

Removing the Old Filter

Start by turning off the water supply valve located behind the refrigerator. This is usually a red or blue lever. Then, disconnect the water line from the filter by twisting the quick-connect fitting counterclockwise. Have a towel ready to catch any water that might dispense.

EveryDrop Water Filter #4 Installation
EveryDrop Water Filter #4 Installation
How to Replace a Filter on Whirlpool W10407342B side-by-side refrigerator
How to Replace a Filter on Whirlpool W10407342B side-by-side refrigerator

Gently pull the old filter out of its housing. It should slide out with a slight twist and pull. Make sure to discard the old filter responsibly, following your local waste management guidelines.

Preparing the New Filter

Before installing the new filter, make sure it's the correct type for your appliance. Check the model number and ensure it matches your specific Whirlpool refrigerator model. Once you've confirmed its compatibility, remove the protective cap from both ends of the new filter.

AD

Wet the O-ring on the filter using distilled or filtered water. This will help create a better seal and prevent air from getting into the system. Also, wet the area around the filter housing and the inlet and outlet areas of the filter to helps seat the filter properly.

Installing the New Filter

Before you install the new filter, note the direction of the arrows on the filter housing and the filter itself. The arrows indicate the direction of water flow, which is usually towards the outlet of the filter housing.

Insert the new filter into the filter housing, ensuring the arrows are in the same direction. Then, gently push the filter in place until it locks securely. You should hear it click into place. Make sure the O-ring on the filter is properly seated against the wall of the filter housing.

AD

Reconnecting the Water Line

Now that the filter is in place, reconnect the water line to the filter by turning the quick-connect fitting clockwise until it's secure. Then, turn the water supply valve back on. Let the water run for about five minutes to purge the system of any air or impurities.

You can now test the water dispenser in your Whirlpool refrigerator. It's a good idea to discard the first few gallons of water to ensure any remaining air or impurities are flushed out.

Programming the Filter Change Indicator

Most Whirlpool refrigerators have a filter change indicator light. To program this, press the 'Filter' button on your refrigerator's control panel. Follow the on-screen instructions to set the indicator to 'Replace'. Your refrigerator will now remind you to replace the filter at the end of its lifespan, typically every 6 months or 400 gallons, depending on your specific model.

AD

That's it! You've successfully installed a new Whirlpool water filter and improved the water quality in your refrigerator. Regularly replacing your water filter helps maintain the purity of your water, keeps your appliance running smoothly, and ensures the longevity of your water dispenser and ice maker.

Remember, installing a water filter isn't just about great-tasting water. It's also about preventative maintenance. So, stay on top of your filter changes to keep your Whirlpool refrigerator in optimal condition. Happy filtered water enjoyment!"

AD