how to install schlage encode

How to Install Schlage Encode

By Joshua Hernandez
AD

Installing a Schlage Encode smart deadbolt on your door not only enhances your home's security but also provides the convenience of locking and unlocking your door using a keypad or your smartphone. Let's walk you through the process, step by step.

Before you start, make sure you have all the necessary tools: a screwdriver (usually a Phillips #2), a drill (in case you need to modify the door), and a little bit of patience. This guide assumes you're replacing an existing deadbolt. If you're installing it on a new door, the process may vary slightly.

Preparation

Start by measuring your door to ensure you have the correct size Schlage Encode. The prep work involves removing the old lock and preparing the door for the new one. If you're unsure about any step, don't hesitate to consult the Schlage manual or a professional.

AD
Install a Schlage Encode WiFi Deadbolt Like a Pro
Install a Schlage Encode WiFi Deadbolt Like a Pro
Schlage Door Smart Lock Install
Schlage Door Smart Lock Install
Schlage Encode - Smart WiFi Deadbolt, how to Install & Amazon Key App Installation ✅
Schlage Encode - Smart WiFi Deadbolt, how to Install & Amazon Key App Installation ✅

Next, uninstall your existing deadbolt. Remove the TH (through-hole) or CL (center-latch) barrel from the door handle set, then take off the interior and exterior escutcheons. Unscrew the interior and exterior halves of the lock, and pull out the latch and torsion bar. Take note of the orientation of the strike plate on the door frame and remove the screws holding it in place.

Inside Latch Installation

With the old lock removed, start by installing the inside latch. Place the door against the frame and position the latch housing against the edge of the door. Mark the drill points and drill holes if necessary. Once drilled, insert the screws to secure the latch housing in place.

Expert Tips for Schlage Encode™ Smart WiFi Deadbolt Install & Setup (BE489)
Expert Tips for Schlage Encode™ Smart WiFi Deadbolt Install & Setup (BE489)
How to install Schlage Encode Smart WiFi Deadbolt with Camelot Trim in Satin Nickel
How to install Schlage Encode Smart WiFi Deadbolt with Camelot Trim in Satin Nickel

Insert the latch into the housing, ensuring it's facing the right way. The quality of the drill bit and your drilling technique can affect the finish, so be careful. Insert the latch retainer and secure it with the provided screw. Reattach the interior escutcheon, aligning it with the turn button and latch.

Exterior Housing Installation

Place the exterior housing against the door, aligning it with the hole you drilled earlier. Secure it with the provided screws, making sure the keyhole is at the top. Position the exterior escutcheon over the housing and align the configurable sidekeeper (if needed) on the correct side.

AD

Install the configuration puff, pushing it in until it clicks, then align the keypad and aesthetic ring. Insert the barrel into the housing and secure it with the provided screw. Then, replace the exterior escutcheon, ensuring it covers the screw heads and that the Schlage logo is right-side up.

Electronics and Keypad Installation

Snap the bezel assembly onto the exterior housing. Position the keypad over the aesthetic ring, aligning the bottom with the edge of the housing. Press the keypad in until the retention clips click into place. Then, snap the battery pack onto the keypad, ensuring it's well-seated.

Replace your door handle set, aligning the TH or CL barrel with the new lock. Secure it with the provided screw. If you're using a lever, push the set lever into the keypad until it clicks, then push the interior rose onto the painted end of the set screw. Align the exterior rose with the set lever and screw it onto the back of the handle.

AD

Final Touches

Test your new Schlage Encode by locking and unlocking it using the keypad and the Schlage app. Register your lock in the app and create user codes. You can also set up auto-lock and other features in the app settings.

Regularly change the battery in your Schlage Encode to ensure optimal performance. Keep the exterior clean and dry to prevent any moisture-related issues. With proper maintenance, your smart lock should serve you well for years to come.

Lastly, remember that smart locks are only as secure as the codes you assign. Use unique codes for each user and change them periodically. Consider using the 'Show Me How' feature in the Schlage app for a visual guide to installation and operation. Enjoy the convenience and security of your new Schlage Encode!

AD
AD