how to install samsung water filter

How to Install Samsung Water Filter: Step-by-Step Guide

By Michael Smith
AD

When it comes to maintaining great-tasting water and ensuring your Samsung water purifier runs smoothly, replacing the filter is a crucial task. But don't worry, the process is straightforward and can be done with no previous DIY experience. Here's a comprehensive guide on how to install a Samsung water filter, optimized for Samsung model numbers RSA7100S, RSA7111S, RSA7112S, RSA7113S, and RSA7120B. Let's dive right in.

Before we start, make sure you have your new Samsung water filter kit, which includes the filter cartridge and filter housing wrench. Also, turn off your water supply and sediment filter to avoid any water leaks or messes.

Preparation

Preparation is key to a hassle-free filter installation. Let's walk through the necessary steps before starting.

AD
Why Does Samsung Water Filter Not Push In?
Why Does Samsung Water Filter Not Push In?
How To Change The Water Filter In A Samsung Refrigerator and Reset Water Filter Light
How To Change The Water Filter In A Samsung Refrigerator and Reset Water Filter Light
Step-by-Step Guide to Samsung Refrigerator Water Filter
Step-by-Step Guide to Samsung Refrigerator Water Filter

First, locate your Samsung water purifier. It's usually installed under the kitchen sink. Next, turn off the water supply valves connected to your purifier. There should be two valves: one for the cold water supply and another for the purified water outlet. Finally, open the faucet connected to your purifier to release any remaining water pressure.

Safety First

Always ensure you're wearing suitable clothing and hazard-free footwear before starting any maintenance task. Place a bucket underneath the purifier to catch any dripping water.

Samsung Refrigerator Water Filter Replacement 🔥 #samsung #waterfilters #replacement
Samsung Refrigerator Water Filter Replacement 🔥 #samsung #waterfilters #replacement
How To Change Your Samsung Fridge Water Filter
How To Change Your Samsung Fridge Water Filter

Additionally, ensure you're comfortable with the space and that the area is well-lit. Remember, safety first.

Identify the Old Filter

Identify the old filter in your Samsung water purifier. It's usually located inside the purifier's grey housing. The housing is typically situated on the right side of the purifier when facing it.

AD

your Samsung water purifier comes with a standard sediment filter (RSA7100S/11S/12S/13S) or an activated carbon filter (RSA7120B). Ensure you replace your filter with the correct one for your model. If you're unsure, consult your user manual or Samsung's official website.

Removing the Old Filter

Now that we're all set, let's remove the old filter. follow these steps to do it correctly.

First, use the provided filter housing wrench to turn the ring counterclockwise. The ring must turn approximately 1/4 turn to release the housing. Once the ring is loose, gently unscrew the housing and lift it up to remove the old filter.

AD

Inspect the O-ring

While you have the housing removed, take a moment to inspect the O-ring. It's the black rubber seal around the housing's base. If it's damaged or worn out, replace it with a new one. A faulty O-ring can cause water leaks.

If your O-ring is in good condition, place it back onto the housing. But if it's damaged, insert the new O-ring into the groove around the housing's base.

Prepare the New Filter

Before installing the new filter, remember to check the installation side. There should be an arrow or 'UP' marking indicating the direction. Your new Samsung water filter should come with the cap removed. If not, gently tap the cap with a hammer to remove it.

AD

Now, gently wipe the filter with a clean, damp cloth to remove any dust or debris. Be careful not to damage the filter surface or contaminate it.

Installing the New Filter

With all the preparation done, it's time to install your new Samsung water filter. Let's proceed carefully.

First, align the new filter with the arrow or 'UP' marking facing up (towards the water supply). Gently insert the filter into the housing. Ensure the filter isn't cross-threaded (diagonally) and that it's straight.

Securing the Housing

Once the new filter is securely in place, align the housing with the hole from which you removed the old filter. Then, place the housing onto the hole, ensuring the O-ring creates a tight seal.

Using the filter housing wrench, tighten the housing clockwise. Tighten it until the ring is securely locked against the housing. The ring should turn in approximately 1/4 turn. However, don't overtighten, as this can damage the housing.

Prime the filter

After installing your new filter, it's crucial to prime it, especially if it has activated carbon. Priming removes trapped air from the filter, ensuring efficient water filtration.

To prime, turn on the cold water tap connected to your Samsung water purifier. Let the water run until it runs clear and you no longer see air bubbles. Typically, this takes around 1-2 minutes.

Replacing the Sediment Filter

If your Samsung water purifier uses a sediment filter (RSA7100S/11S/12S/13S), this process is slightly different. Here's how to replace the sediment filter.

The sediment filter change process is similar to the activated carbon filter change process. However, the sediment filter doesn't have a cap and looks like a white cylindrical tube.

Installation

First, insert the new sediment filter into the housing. Align the arrow or 'UP' marking on the filter with the marking on the housing. Then, secure the housing with the filter housing wrench.

Compare the four sides of the housing. On two opposite sides, there are recesses. Align these recesses with the corresponding tabs on the valve. This alignment allows you to insert the filter housing onto the valve.slide the filter housing onto the valve, ensuring the O-ring creates a tight seal.

Priming the Sediment Filter

Since the sediment filter doesn't have a cap, priming isn't strictly necessary. However, running water through the filter helps remove any impurities accumulated during storage.

To prime, simply turn on the cold water tap connected to your Samsung water purifier and let the water run for about 30 seconds. Now, your filtered water is ready to use.

Congratulations! You've successfully installed a new Samsung water filter. Regularly replacing your filter ensures clean, sparkling water. Don't forget to replace your filter every 6 months or as recommended by Samsung, depending on your water quality and usage. Happy filtering!

AD