how to install rear outlet toilet

Step-by-Step Guide: Install Rear Outlet Toilet

By Nicole Wilson
AD

Installing a rear outlet toilet, also known as a soil stack toilet, can be a complex task, but with the right guidance, it's entirely achievable. This step-by-step guide will walk you through the process, from preparation to completion, ensuring your new toilet is securely and efficiently installed. Let's dive into the details.

Before starting, you'll need to gather your tools and materials. You'll need a toilet, a wax ring,ebolts, nuts, screwdriver, drill (if using bolts), adjustable wrench, hacksaw, level, and wax or plumber's putty, depending on your toilet's make and model.

Preparation and Measurement

Before you begin, ensure your toilet is compatible with your existing plumbing. Rear outlet toilets require a drain pipe at the rear of the toilet, which typically aligns with a 3- or 4-inch pipe. Measure your existing drain to ensure a proper fit.

AD
How to Install a Rear Outlet Toilet
How to Install a Rear Outlet Toilet
How to Install a Rear Outlet Toilet
How to Install a Rear Outlet Toilet
How to Install a Rear Outlet Toilet
How to Install a Rear Outlet Toilet

Next, measure the space for your new toilet. Most toilets are 16.5 to 21 inches between the wall and the center of the bolt circle. Make sure your new toilet fits the space and allows for comfortable access.

Removing the Old Toilet

Start by turning off the water supply and flushing the toilet to drain the tank and bowl. Disconnect the water supply line and remove the tank bolts to separate the tank from the bowl. Remove the nuts and bolts or plastic caps from the bowl and carefully lift off the old toilet. Clean the floor to prepare for the new installation.

How To Install A Toilet
How To Install A Toilet
an image of how to install a rear exit toilet in your home or office area
an image of how to install a rear exit toilet in your home or office area

If your old toilet had a wax ring, make sure to scrape off any remaining wax from the soil stack with a utility knife or scraper. Also, check the bolts on the floor and replace them if necessary. Newer toilets typically use bolts with a threaded nipple, but older toilets may use smooth bolts. If yours are smooth, you'll need to chisel a nipple into the concrete or use bolts with a long shaft and a nut and washer.

Preparing the New Toilet

Unpack your new toilet and lay it on its side, preferably on a soft surface like a blanket or towel. Attach the tank to the bowl, ensuring the gasket on the tank's bottom is properly aligned. If your toilet comes with a new bolt set, install them now. Align the hole in the bottom of the tank with the bolt circle and secure it with the bolts and washers provided.

AD

Next, place a wax or plumber's putty ring over the horn on your new toilet. If you're using a wax ring, ensure it's seated properly and the wax is pointing downward. For plumber's putty, roll it into a snake shape, place it around the horn, and smooth it with your finger. These rings create a seal between the toilet and the soil stack, preventing leaks.

Installing the Toilet

With everything prepared, it's time to install your new toilet. Place the horn of the toilet over the soil stack pipe, ensuring the toilet is properly aligned with the bolts on the floor. Carefully lower the toilet until the bolts fit through the holes in the base.

Once the bolts are through, carefully lift the toilet until the wax or putty ring makes contact with the soil stack, creating a seal. Hold the toilet in place and tighten the bolts using a互调 wrench. Remember, not all toilets come with washers, so check your hardware kit before installation. Tighten the bolts one-third of the way, then alternatetightening and loosening each about an eighth of a turn to avoid cracking the toilet's base.

AD

Securing the Toilet

With the bolts secured, place washers over the bolts and secure them with their corresponding nuts. Use an adjustable wrench to tighten the nuts, again alternating to avoid cracking the base. Be careful not to overtighten, as this can cause leaks or break the toilet.

Once the nuts are tight, use a level to ensure the toilet is balanced and secured properly. If necessary, gently tap the bolts or the base with a rubber mallet to level the toilet. Wipe away any excess wax or putty with a damp cloth.

Connecting the Water Supply

Reconnect the water supply line, ensuring it's securely attached and the connection is watertight. Turn the water supply valve on slowly to avoid busting any lines. Check for leaks around the supply line and the soil stack, tightening any loose connections if necessary.

AD

Flush the toilet to test the system. The water should drain quickly and the tank should refill. If everything works as it should, you've successfully installed your rear outlet toilet!

Regularly check your toilet for leaks and cracks, ensuring its proper functioning. A well-maintained toilet can last for decades, making your installation efforts worth it in the long run. Enjoy your newly installed toilet and the peace of mind that comes with knowing you've done a thorough job.

AD