how to install pod filters on a motorcycle

How to Install Pod Filters on a Motorcycle

By Christopher Brown
AD

Ever wondered how to boost your motorcycle's performance and reduce emissions? Installing pod filters is a cost-effective way to achieve this. Pod filters allow more air to enter the engine, enhancing its efficiency and churning out more power. Here's a step-by-step guide on how to install pod filters on your motorcycle.

Before you get started, gather your materials. You'll need the pod filter kit, a flathead screwdriver, a ratchet, sockets, and maybe some Allen keys. It's also a good idea to have your motorcycle's owner's manual handy. This guide assumes you have basic mechanical knowledge and tools.

Understanding Pod Filters

Pod filters consist of two parts: the filter element and the outer pod. The filter element traps dirt and debris, while the pod houses the filter and bolts onto your motorcycle's airbox or intake pipe. By replacing your stock filter with a pod filter, you increase airflow and improve engine performance.

AD
The Pros & Cons Of Motorcycle Pod Filters - Jalopnik
The Pros & Cons Of Motorcycle Pod Filters - Jalopnik
an advertisement with the words, do you know why your airbox is important?
an advertisement with the words, do you know why your airbox is important?
NIBBI moto PE carburateur CNC filtre à Air Kit PE24/26/28/30mm puissance Jet Carb modifié FitHonda
NIBBI moto PE carburateur CNC filtre à Air Kit PE24/26/28/30mm puissance Jet Carb modifié FitHonda

Pod filters come in various sizes and types, so make sure to choose one compatible with your motorcycle's make and model. Some pod filters are reusable, while others are disposable. Reusable filters might require occasional cleaning, while disposable ones typically last for 15,000 to 20,000 miles before needing replacement.

Removing the Stock Filter

Before installing your new pod filters, you need to remove the stock filters. Start by disconnecting the negative battery cable to prevent any electrical shorts. Then locate your motorcycle's airbox or intake pipe, usually found near the throttle body.

Removing the factory air box: Installing an aftermarket...
Removing the factory air box: Installing an aftermarket...
closeup of the air filter on a motorbike with gold and purple details
closeup of the air filter on a motorbike with gold and purple details

Using a flathead screwdriver or a pick tool, carefully pry off the airbox cover or intake pipe's rubber plugs. With the cover or plugs removed, you can now access the stock filters. Use a ratchet and appropriate socket to unscrew the filter cover's bolts. Gently push the cover outwards to release it from the rubber grommet, and remove the stock filters.

Cleaning the Airbox or Intake Pipe

With the stock filters removed, inspect the airbox or intake pipe for any dirt or debris buildup. Use compressed air to clean out the area, ensuring no dirt enters the engine when you install the pod filters.

AD

For added protection, consider applying a small amount of grease to the rubber grommet where the filter mounts. This helps create a better seal, reducing the risk of contaminants entering the engine. Be careful not to use too much, as excessive grease can attract dirt and lasciare the filter more susceptible to clogging.

Preparing the Pod Filters

Before installing the pod filters, ensure the filter elements are properly seated within the pods. Some filters may require additional prep, such as trimming the seal to ensure a proper fit or oiling the filter element.

Most pod filters use a cable-tie system for securing them to the intake pipe or airbox. Thread the cable tie through the provided hole on the pod and around the intake pipe or airbox, then pull tight and cut off any excess. Make sure the pod is securely attached and won't vibrate loose while riding.

AD

Installing the Pod Filters

Now that your airbox or intake pipe is clean and the pod filters are prepared, it's time to install them. Carefully position the pod filter over the intake pipe or airbox, ensuring the cable tie is on the correct side and won't interfere with any other components.

Using a ratchet and appropriate socket, bolt the pod filter securely in place. Tighten the bolts evenly and snugly, ensuring no gaps remain between the pod filter and the intake pipe or airbox. Be cautious not to overtighten, as this can cause the bolts to break or strip.

Reassembling the Intake System

With the pod filters securely fastened, reattach the rubber plugs or airbox cover. Ensure the seals are properly seated and there are no air leaks. If you greased the rubber grommet earlier, make sure the grease isn't leaking out or attracting dirt.

AD

Reconnect the negative battery cable and start your motorcycle. Allow the engine to idle for a few minutes, checking for any air leaks or unusual noises. Once you're satisfied with the installation, take your motorcycle for a short ride to ensure proper function and performance.

Maintaining Your Pod Filters

Regular maintenance is crucial to keep your pod filters performing at their best. Depending on the type of pod filter you have, you may need to clean or replace them every 5,000 to 15,000 miles. Consult your motorcycle's owner's manual for specific maintenance intervals.

Cleaning reusable filters typically involves removing the filter element, disassembling it, and using compressed air or a specialized cleaning kit to blow off the dirt. Allow the filter to air dry completely before reoiling and reassebling it. Always follow the manufacturer's instructions for proper cleaning and oiling techniques.

With regular maintenance and proper installation, pod filters can significantly improve your motorcycle's performance and reduce emissions. By following this guide, you've taken the first step towards unlocking your motorcycle's true potential. Happy riding!

AD