how to install hei distributor on chevy 350

Step-by-Step: How to Install HEI Distributor on Chevy 350

By James Jackson
AD

So, you've decided to upgrade your Chevy 350's ignition system with a HEI (High Energy Ignition) distributor? You're in the right place. This comprehensive guide will walk you through the process, step by step, ensuring a smooth and successful installation. Let's dive in.

Before we start, ensure you have the right tools and parts. You'll need a HEI distributor,of course, along with a new ignition module, spark plug wires, and new spark plugs. Additionally, grab a ratchet and socket set, a breaker bar, a 1/8" Allen wrench, and a feeler gauge.

Understanding the HEI Distributor

The HEI distributor is an improvement over the original points-type distibutor. It uses a(n) electronically controlled ignition system, providing better spark and efficiency.

AD
an orange and black machine with wires attached to it's front end, sitting on top of a pile of metal parts
an orange and black machine with wires attached to it's front end, sitting on top of a pile of metal parts
GM HEI electronic distributor how to wire and run install DIY
GM HEI electronic distributor how to wire and run install DIY
How To Install a Distributor in a Small Block Chevy Engine
How To Install a Distributor in a Small Block Chevy Engine

Before we jump into the installation, let's quickly understand what comes in the HEI distributor kit. Typically, it includes the distributor body, the rotor, the pick-up coil, the ignition module, and the spark plug wires.

Components of the HEI Distributor

The HEI distributor has several components that work together to ensure your engine fires properly. The distributor body houses the internal parts, the rotor directs the spark to the correct cylinder, the pick-up coil generates the spark, and the ignition module controls the timing.

The Lost Art of Servicing GM HEI
The Lost Art of Servicing GM HEI
MSD to GM HEI Distributor Harness - MSD Ignition
MSD to GM HEI Distributor Harness - MSD Ignition

Familiarizing yourself with these components will help you understand how the system works and how to diagnose any issues that might arise in the future.

Preparation and Removal of the Old Distributor

Before you start, ensure your engine is cold to avoid any burns. Disconnect the negative battery cable to prevent any electrical shorts.

AD

Now, let's remove the old distributor. Start by disconnecting the distributor cap and wires. Then, use a ratchet and socket to loosen and remove the distributor hold-down clamp. Once that's off, you should be able to pull the distributor out of the engine.

Installing the HEI Distributor

Now that you have the old distributor out, let's install the new HEI distributor. The process is largely reversed, but with a few additional steps.

First, position the HEI distributor into the engine block. Ensure the keyway on the distributor shaft aligns with the keyway in the engine's crankshaft position sensor (or trigger wheel). This ensures the distributor is correctly timed.

AD

Timing the HEI Distributor

Timing the distributor is crucial for proper engine operation. Refer to your Chevy 350's service manual for the correct initial timing specification. Typically, it's around 10-14 degrees Before Top Dead Center (BTDC) at idle.

Once you've set the initial timing, connect the ignition module to the distributor. Route the wires properly, ensuring they won't get caught on anything as the engine operates. Reconnect the negative battery cable.

Setting the Spark Plug Gap and Connecting the Wires

Before installing the new spark plugs, use a feeler gauge to set the gap to the manufacturer's specification, usually around 0.025" to 0.035". Then, install the new spark plugs and connect the HEI spark plug wires.

AD

Ensure you connect the wires to the correct cylinder, following the rotational order of the engine. The firing order for a Chevy 350 is 1-8-4-3-6-5-7-2.

Testing and Final Touches

Now that your HEI distributor is installed, it's time to test the system. Start the engine and let it idle. Check for any unusual noises or signs of trouble.

Next, give the engine a rev, listening for any irregularities. If everything sounds good, let the engine warm up. Keep an eye on your temperature gauge and listen for any changes in engine noise.

Tuning and Adjustments

After the engine has warmed up, turn off the ignition and let the engine cool slightly. This allows you to recheck and adjust the ignition timing if necessary.

Also, use this opportunity to double-check your spark plug connections and gaps. If everything checks out, start the engine and enjoy the improved performance of your HEI distributor.

Congratulations! You've just successfully installed a HEI distributor on your Chevy 350. Regular maintenance and occasional checks will keep your engine running smoothly. Happy motoring!

AD