how to install a distributor chevy 350

How to Install a Distributor on a Chevy 350: Step-by-Step Guide

By Anthony Walker
AD

Tackling the task of installing a distributor on a Chevy 350 engine might seem daunting, but with the right guidance, it can be a rewarding experience that enhances your mechanical skills. This step-by-step guide will walk you through the process, ensuring a successful installation that keeps your engine purring like a kitten.

Before we dive into the nitty-gritty, let's ensure you have the correct distributor for your Chevy 350. The most common are the HEI (High Energy Ignition) distributors, but there are other types like thePoints series and the conventional distributors. Double-check your application's requirements to avoid any unnecessary headaches.

Preparation: Disassembly and Gathering Tools

Before you begin, gather all the necessary tools. You'll need a socket and wrench set, spark plug socket, breaker bar, extension, pliers, and perhaps a distributor wrench if not included in your tool kit. Ensure your work area is clean and well-lit to avoid any mishaps.

AD
Cranky Chevy 350 Distributor Install is Late at Top Dead Center
Cranky Chevy 350 Distributor Install is Late at Top Dead Center
How to Install A distributor in a 350 Chevy
How to Install A distributor in a 350 Chevy
How to Install a Distributor and Set Initial Timing
How to Install a Distributor and Set Initial Timing

Begin by disconnecting the negative battery terminal to prevent any short circuits. Once you've done that, you're ready to remove the old distributor. First, mark the relationship of the distributor and engine block with a grease pencil or white paint. This will help you reinstall the correct timing.

Removing the Old Distributor

Starting from the top, remove the spark plug wires from the cap, then unclip the cap from the distributor. Beneath the cap, you'll find the rotor. Remove it by gently prying it off with a flathead screwdriver. Next, unbolt the distributor hold-down clamp and carefully pull the distributor out, ensuring it doesn't get damaged.

How to Install A distributor in a 350 Chevy
How to Install A distributor in a 350 Chevy
Install a Distributor & set Ignition Timing (How To)
Install a Distributor & set Ignition Timing (How To)

Once removed, you'll notice a lignotek or woodruff key at the bottom. This key synchronizes the distributor with the crankshaft. If yours is worn out, you might need to replace it. Take note of the key's position in relation to the keyway to aid in reinstallation.

Inspecting and Preparing the New Distributor

Before installing the new distributor, thoroughly clean it to remove any contaminants. If it's an HEI distributor, ensure the points cover is well-seated and the points are at the correct gap ( typically 0.016 to 0.018 inches). For other types, check the points gap, rotor, and cap condition. A new distributor should come preset, but double-check to ensure everything is in order.

AD

Also, inspect the distributor shaft and the area where it interfaces with the engine block. Any signs of wear could lead to timing issues, so replace the distributor if necessary.

Installing the New Distributor

Now that you've got your new distributor ready, it's time to install it. First, insert the lignotek key into the distributor shaft, ensuring it corresponds with the mark you made earlier. If your engine is stroker or modified, consult your specific engine's requirements for the correct timing mark.

With the key installed, position the distributor into the engine block, aligning the key with the keyway. Gently push the distributor into place, being careful not to damage the dowel pins or oil seal. Once it's seated, reattach the distributor hold-down clamp and tighten it securely.

AD

Reconnecting the Wires and Spark Plugs

The next step involves reattaching the spark plug wires. Consult your vehicle's repair manual to determine the correct firing order. Typically, it's 1-8-4-3-6-5-7-2 for Chevy 350 engines. Replace the spark plug wires one at a time, ensuring each wire is correctly seated on its respective cylinder.

Once all spark plug wires are connected, reattach the distributor cap and rotate the engine by hand to ensure everything turns smoothly. If there's any resistance, double-check your work and ensure nothing is causing a blockage.

Final Touches and Testing

Reconnect the negative battery terminal, then start the engine. Let it idle and listen for any unusual noises. If the engine seems to be running poorly, you might need to adjust the timing. However, this should only be done with specialized tools and knowledge, as improper timing can damage your engine.

AD

Once you're satisfied with how the engine is running, let it idle and warm up. Monitor the temperature gauge to ensure everything runs within the normal range. After the engine has warmed up, take it for a short test drive, keeping the RPMs low to avoid revving the engine too high too soon.

Congratulations, you've successfully installed a new distributor on your Chevy 350! Regular maintenance, like checking and cleaning the spark plugs, will ensure your engine continues to perform at its best. Happy driving!

AD