how to install exhaust gaskets on a harley

Step-by-Step: How to Install Exhaust Gaskets on a Harley

By Thomas Moore
AD

An exhaust gasket is a critical part of a Harley-Davidson motorcycle, ensuring a proper seal between the exhaust header and the engine, preventing leaks, and maintaining performance. If your gasket shows signs of wear or failure, it's essential to replace it promptly. Here's a step-by-step guide on how to install exhaust gaskets on a Harley Davidson motorcycle.

Before you begin, gather all the necessary tools and parts. You'll need a new exhaust gasket, TCP (Thread Chaser Paste), a socket and wrench set, an exhaust stud remover and installer, a new set of exhaust stud nuts, and a torque wrench.

Preparation: Removing the Old Exhaust System

Begin by removing the Harley Davidson exhaust pipe. Loosen and remove the exhaust pipe mounting nuts using your socket and wrench set. Carefully slide the exhaust pipe backwards and off the exhaust header.

AD
How to Install Slip-On Exhaust on Harley Davidson - Quick & Easy!
How to Install Slip-On Exhaust on Harley Davidson - Quick & Easy!
5 Harley-Davidson mods to do before exhaust
5 Harley-Davidson mods to do before exhaust
Motorcycle Exhaust Pipes
Motorcycle Exhaust Pipes

Inspect the exhaust header for any signs of damage or wear. If everything looks good, proceed to remove the old gasket. Use an exhaust stud remover to carefully pry off the old gasket, ensuring not to damage the exhaust header or the engine block.

Preparing the Exhaust Header and Engine Block

Once the old gasket is removed, clean both the exhaust header and the engine block using a suitable solvent or degreaser. This will ensure there's no residue or old debris that could interfere with the new gasket's seal.

How to clean motorcycle exhaust pipes │SWISSBIKER
How to clean motorcycle exhaust pipes │SWISSBIKER
Create a Custom 2 Stroke Exhaust System - DIY Expansion Chamber.
Create a Custom 2 Stroke Exhaust System - DIY Expansion Chamber.

Apply a thin layer of TCP (Thread Chaser Paste) to the exhaust studs. This will help lubricate the threads and prevent seizing. Wipe off any excess paste with a clean rag.

Installing the New Gasket

Position the new exhaust gasket in place between the exhaust header and the engine block. Ensure the gasket is properly aligned with the exhaust ports and that it covers the entire mating surface.

AD

Press the exhaust gasket firmly into place using your hands. Do not force the gasket, as this could damage it. Once the gasket is in place, carefully insert the exhaust studs through the gasket and the engine block.

Securing the Exhaust Pipe

Reinstall the exhaust pipe by sliding it onto the exhaust header andvid the exhaust gasket. Position the exhaust pipe mounting nuts over the exhaust studs and hand-thread them onto the studs.

The exhaust pipe should now be loosely attached to the exhaust header. Use your torque wrench to tighten the exhaust pipe mounting nuts to the factory-recommended specification. For Harley Davidsons, this is typically around 25 ft-lbs (34 Nm) for post-1999 models and 18-22 ft-lbs (24-30 Nm) for pre-1999 models.

AD

Final Checks and Adjustments

After securing the exhaust pipe, give the system a gentle tug to ensure it's properly seated. Recheck the torque on the exhaust pipe mounting nuts to ensure they're still within the recommended specification.

Start your Harley and let it idle for a few minutes, allowing the exhaust system to heat up. Listen for any leaks or unusual noises. If everything sounds good, your new exhaust gasket should be properly installed and ready for the road.

Ride responsibly and enjoy the peace of mind that comes with knowing you've performed a critical maintenance task on your Harley Davidson motorcycle. Regularly inspecting and maintaining your exhaust system will ensure many miles of reliable, safe riding.

AD
AD