how to install compression shut off valve

How to Install Compression Shut Off Valve: Step-by-Step Guide

By Sarah Williams
AD

Installing a compression shut off valve can significantly improve the efficiency and lifespan of your plumbing system. Popular in modern HVAC and plumbing systems, these valves automatically shut off water flow when the system's pressure drops below a certain level. Here's a step-by-step guide on how to install a compression shut off valve, designed for both homeowners and professional plumbers.

Before you start, make sure you have the following tools and materials: compression shut off valve, adjustable wrenches, pipe cutter or hacksaw, Teflon tape, and a Soldiers Key or basin wrench. This guide assumes you're replacing an existing valve and familiar with basic plumbing.

Preparation and Valve Selection

Choose a bidirectional valve if your pipes can carry water in two directions. Select a diameter that matches your existing pipe size. Standard compression fittings come in 1/4", 3/8", 1/2", and 3/4".

AD
How to Install Shut-Off Valves - The Home Depot
How to Install Shut-Off Valves - The Home Depot
How to install a compression fitting gate valve
How to install a compression fitting gate valve
How To Install a BrassCraft® Compression Valve
How To Install a BrassCraft® Compression Valve

Before you begin, ensure your water supply is turned off at the main valve. Drain residual water by opening nearby faucets and turning off the heating system to prevent airlocks.

Removing the Existing Valve

Using an adjustable wrench, loosen the nut connecting the valve to the pipe. Turn the nut counterclockwise until it's fully loose, then remove it by hand. Unscrew the valve from the pipe using a Soldiers Key or basin wrench. If the valve doesn't budge, spray some penetrant oil on the threads and wait for 15 minutes before trying again.

How To Remove/Install a LEAKY/NEW SHUT-OFF Valve (Compression, Soldered or Push fit) | GOT2LEARN
How To Remove/Install a LEAKY/NEW SHUT-OFF Valve (Compression, Soldered or Push fit) | GOT2LEARN
a close up of an electrical outlet on a wall with copper pipes attached to it
a close up of an electrical outlet on a wall with copper pipes attached to it

If the valve is seized, you may need to cut the pipe. Mark the pipe with a grease pencil, then use a pipe cutter or hacksaw to carefully cut through the pipe. Deburr the cut ends using a file or sandpaper.

Measuring and Preparing the New Valve

Measure the center-to-center distance of the pipe ends. Choose a valve with a similar center spacing. If it's different, you may need to adjust your pipe lengths or choose a different valve.

AD

Prepare the new valve by applying two wraps of Teflon tape around the male thread of each valve inlet. This creates a watertight seal and helps prevent leaks.

Installing the Compression Shut Off Valve

Position the new valve between the two pipe ends. Match the inlet ports to the corresponding pipe diameters. Align the passages of the valve body with the pipe centerlines.

Hand-tighten the valve onto the first pipe end, turning it clockwise. Use a Soldiers Key or basin wrench to secure the fitting, applying equal force on both sides. Tighten it until the nut is fully engaged with the valve body, then give it an additional 1/4 to 1/2 turn.

AD

Securing the Second Pipe End

Hand-tighten the valve onto the second pipe end, ensuring it's properly aligned. Secure the fitting with an adjustable wrench, tightening it by an equal amount on both sides. Again, give it an additional 1/4 to 1/2 turn.

Reตรฝ σχ tônca tinhamr cettee procedures carefully. SIO DO NOT OVERHOUGHEN, which can cause leaks or damage the valve.

Testing the Installation

Slowly open the valve to the full open position. Turn on the main water supply valve. Check for leaks at all connection points. Turn off the main valve and reassess the system.

AD

To test the valve's functionality, partially close it, then open a nearby faucet. The valve should allow water to flow until the pressure drops, then automatically shut off. Close the faucet and reopen the valve to check if it works correctly.

Congratulations, you've successfully installed a compression shut off valve! Regularly inspect your valve for leaks and proper functioning to ensure your plumbing system remains in top condition. If you're unsure about any part of the process, don't hesitate to consult a professional plumber.

AD