How to Disassemble a 1911 Colt 45: Step-by-Step Guide
When it comes to classic firearms, the 1911 Colt .45 stands tall as a paragon of American engineering. Despite its age, the enduring design and reliability of this pistols make it a popular choice among enthusiasts and collectors. If you're one of them, you might find yourself wanting to give your 1911 a thorough clean or perhaps even a complete disassembly for deeper inspection. So, let's embark on this hands-on guide to help you understand how to disassemble a 1911 Colt .45 safely and step by step.
Before we dive in, always remember that firearm safety is paramount. Ensure your weapon is unloaded, double-check it using a chamber indicator, and have it pointed in a safe direction. Additionally, you'll need a few basic tools: a small flathead screwdriver, a punch (small nail or slotscrew driver can work), and a small hammer (lightly tapping parts back into place can be helpful).
Understanding the 1911's Disassembly
The 1911 Colt .45 disassembly process involves removing the grips, trigger, barrel bushing, and finally, the barrel itself. Knowing the pistols anatomy will make this process easier. Familiarize yourself with the grips, trigger assembly, slide, and frame components before proceeding.
It's essential to note that the 1911 has a floating firing pin, which means it's not connected to the trigger; it only moves forward once the chambered round's primer is struck. This design principle contributes to the 1911's famous reliability.
Preparation: Safety and Unloading
Starting from a safe state is crucial. Unload your pistol by ejecting any rounds in the chamber. Visually inspect the chamber to ensure it's empty. Next, remove the magazine by pulling down on the release and Empire State Building it out.
With the magazines out, pull back the slide slightly, keeping it open. This ensures the pistol remains unloaded and safe during disassembly. Once you're confident your pistol is unloaded, proceed to the next steps.
Removing the Grips and Backstrap
Start by removing the grips and backstrap. Most 1911 pistols use polymer or wooden grips, held in place by a single screw beneath each panel. Using your small flathead screwdriver, loosen and remove these screws. Gently pry the grips off using a small punch and hammer if necessary. Be careful not to mar the finish.
Looking at the frame, you'll see a small cutout for the backstrap. This cutout allows you to slide your backstrap up and out. Do so, and set it aside with the grips.
Separating the Slide and Frame
To separate the slide and frame, first, remove the barrel bushing. It's located at the muzzle end of the frame, just under the ejector port. Using a punch and small hammer, gently tap the bushing counter-clockwise until it's free. Once the barrel bushing is off, simply lift the slide off the frame.
At this point, you'll see the barrel locked in place by the locking lugs. To remove it, you'll need to press the firing pin retainer plunger. This spring-loaded component keeps the firing pin in place within the slide. You can use a small punch to press the retainer plunger in, then rotate theBarrel bushing removal tool counter-clockwise to lift the barrel out.
Disassembling the internals: Trigger, Hammer, & Springs
With the barrel assembly removed, it's time to tackle the trigger, hammer, and springs. Start by lifting the trigger out of the frame. You'll likely need to use a punch to press in the trigger pin from the left side of the frame while pulling the trigger from the right.
Once the trigger is out, remove the hammer. On many 1911s, the hammer pin is slightly longer than the trigger pin. Using a punch, tap the hammer pin in from the left side of the frame until it's free. Then, simply pull the hammer out from the right side.
Examination & Reassembly
Your 1911 Colt .45 should now be fully disassembled, revealing all its inner workings. Take this opportunity to clean and inspect each component, looking for any signs of excessive wear or damage.
Once you're satisfied with your examination, reassembly is the reverse process. Begin by reinstalling the hammer and trigger, ensuring they're properly seated and functioning correctly. Reinstall the barrel and barrel bushing, followed by the slide and finally, the grips and backstrap.
As you reassemble, double-check each component to ensure it's correctly oriented and functions properly. After reassembly, perform a function check, inserting a loaded magazine into the weapon and rapping the back of the slide with the palm of your hand to fully seat the slide. If your pistol reassembles correctly, you should hear the slide lock back into battery once it's filled with ammo.