how to diagnose crank no start

How to Diagnose a Crank No Start Situation

By Christopher King
AD

Have you found yourself in a frustrating situation where your vehicle's engine refuses to turn over, leaving you stranded? This common issue is often referred to as a "crank no start" condition. This article will guide you through a step-by-step diagnostic process to help you understand and potentially resolve this predicament.

Before diving into the diagnostic steps, ensure that your vehicle's 12-volt battery is in good condition and properly secured. A weak or dead battery can simulate a crank no start issue. If the battery checks out, let's proceed with the diagnostic process.

Understanding the Components

To diagnose a crank no start issue effectively, it's essential to understand the key components involved in the engine's starting process. These include the ignition switch, starter relay/solenoid, starter motor, and the engine's computer (ECM/PCM). Familiarize yourself with these components before starting the diagnostic process.

AD
How to Diagnose a No Crank No Start Issue - Nothing or only a Click When the Key is Turned
How to Diagnose a No Crank No Start Issue - Nothing or only a Click When the Key is Turned
Crank No-Start Diagnosed only with Test Light
Crank No-Start Diagnosed only with Test Light
No Crank No Start troubleshooting HACK TEST. This where you should do all your TESTING. PT Cruiser
No Crank No Start troubleshooting HACK TEST. This where you should do all your TESTING. PT Cruiser

Now that you're familiar with the key components let's move on to the diagnostic steps.

Step-by-Step Diagnosis

1. Inspect the Ignition Switch and Starter Relay/Solenoid

Begin by inspecting the ignition switch and starter relay/solenoid for any visible damage or corrosion. If you find any issues, these components may be the cause of the problem. Replacing the faulty component should resolve the issue. If these components appear to be in good condition, proceed to the next step.

To further test the ignition switch and starter relay/solenoid, use a multimeter to measure the resistance across the terminals while turning the ignition key to the "start" position. Compare the readings to the manufacturer's specifications, and replace any components that fall outside the acceptable range.

2. Test the Starter Motor

Next, inspect the starter motor for any visible signs of damage or displacement. If the starter motor appears to be in good condition, use a multimeter to test its continuity. A properly functioning starter motor should have continuity (low resistance) between its battery terminal (B+) and the engine-side terminal (S). If the motor fails this test, replace it.

Before testing the starter motor's continuous draw, ensure that the ignition switch and starter relay/solenoid have been adequately tested. To test the continuous draw, connect a multimeter in series with the starter motor's battery terminal (B+) and measure the current draw while cranking the engine. A healthy starter motor should draw between 150-250 amps, depending on the vehicle's make and model.

Additional Diagnostic Steps

If the inspection and tests mentioned above have not revealed any issues, proceed with the following diagnostic steps to pinpoint the problem.

Inspect the engine's wiring harness and connections for any signs of damage, corrosion, or poor connections. Tighten or repair any discrepancies found, and re-test the system.

3. Verify the ECM/PCM Compatibility

Although rare, a malfunctioning ECM/PCM can cause a crank no start condition. Use an OBD-II scanner to retrieve any diagnostic trouble codes (DTCs) stored in the computer's memory. If a DTC related to the starting system is present, further diagnosis may be required to pinpoint the exact cause. Consult the vehicle's repair manual for guidance.

If no DTCs are present, or if the stored DTC does not relate to the starting system, you may need to perform more in-depth testing, such as charging system analysis or fuel pressure testing. However, these tests are beyond the scope of this article.

In conclusion, diagnosing a crank no start condition requires a systematic approach and a solid understanding of the vehicle's starting system components. By following the steps outlined in this article, you can save time and money by accurately determining the cause of the issue. If the problem persists despite your best efforts, consult a professional technician for further assistance.

How to Diagnose an Engine that Turns Over and Cranks But Does Not Start - Crank No Start Diagnosis
How to Diagnose an Engine that Turns Over and Cranks But Does Not Start - Crank No Start Diagnosis
How To Diagnose Cranking No-Start Conditions
How To Diagnose Cranking No-Start Conditions
AD