how to clean a carburetor snowblower

How to Clean a Carburetor on Your Snowblower

By Olivia Garcia
AD

Is your snowblower struggling to start or losing power while clearing your driveway? A clogged carburetor could be the culprit. Here's a step-by-step guide on how to clean a snowblower carburetor to restore peak performance and ensure a smooth winter clearing season.

Remember, routine maintenance is key to keeping your snowblower running smoothly. Cleaning the carburetor regularly should be part of your seasonal snowblower maintenance checklist.

Understanding Your Snowblower Carburetor

Before diving into the cleaning process, let's quickly discuss what a carburetor does. In simple terms, it's responsible for mixing air and fuel before feeding it into the engine. In a snowblower, the carburetor helps maintain the correct air-to-fuel ratio, ensuring optimal engine performance.

AD
HOW TO CLEAN A CARBURETOR ON A CRAFTSMAN 179CC SNOWBLOWER FOR BEGINNERS
HOW TO CLEAN A CARBURETOR ON A CRAFTSMAN 179CC SNOWBLOWER FOR BEGINNERS
How to clean a snowblower carburetor 2022 (Solved)
How to clean a snowblower carburetor 2022 (Solved)
Best Tips In Cleaning A Snowblower Carburetor To Keep It In Good Condition
Best Tips In Cleaning A Snowblower Carburetor To Keep It In Good Condition

Understanding this function helps you identify signs of a clogged carburetor, such as difficulty starting, poor acceleration, and a decrease in power.

Gathering Your Tools and Supplies

Before you begin, gather the necessary tools and supplies. You'll need:

Best Tips In Cleaning A Snowblower Carburetor To Keep It In Good Condition
Best Tips In Cleaning A Snowblower Carburetor To Keep It In Good Condition
Best Tips In Cleaning A Snowblower Carburetor To Keep It In Good Condition
Best Tips In Cleaning A Snowblower Carburetor To Keep It In Good Condition
  • Rags or shop towels
  • Carburetor cleaner spray (such as WD-40 Specialist® Carb/Choke & Parts Cleaner)
  • Needle-nose pliers
  • Screwdriver (flathead or Phillips, depending on your snowblower model)
  • Small wire brush

Safety First: Disconnect the Spark Plug and Fuel Line

Before you start dismantling your snowblower, ensure it's safe to work on by disconnecting the spark plug wire and laying it aside to prevent accidental starting. Next, tilt the snowblower on its side and remove the fuel line at the carburetor.

Dismantling the Carburetor

Now that your snowblower is safe to work on, let's remove the carburetor. Begin by removing the air filter housing and filter to expose the carburetor.

AD

Locate and remove the two or four screws (depending on your snowblower model) securing the carburetor to the engine. Carefully pull the carburetor away from the engine. You might need to use needle-nose pliers to gently pull out the fuel line at the carburetor inlet. Set the carburetor down with its bowl facing up to avoid fuel spills.

Cleaning the Carburetor Exterior and Bowl

Inspect the exterior of your carburetor for any visible dirt, debris, or signs of rust. Use a rag dampened with carburetor cleaner to thoroughly clean the exterior, paying close attention to the intake and outlet areas.

Remove the float bowl by gently prying it loose using a flathead screwdriver. If necessary, use needle-nose pliers to carefully remove the bowl. Once removed, clean the bowl and the area where it sits with a rag and cleaner. Use a small wire brush to scrub any heavy dirt or rust away.

AD

Cleaning the Carburetor Needles and Jet

Locate the main jet and idle mixture screws on the side of the carburetor. They might be marked with 'M' for mixture and an arrow indicating their function. Using a flathead or Phillips screwdriver, very carefully back these screws out a quarter to a half turn at a time. Be cautious not to overtighten or undertighten them, as this can throw off your snowblower's idle and acceleration.

With the screws slightly backed out, spray some carburetor cleaner into the holes and allow it to soak for a few minutes. Next, use a small wire brush to clean out any dirt or residue around the needle and jet. Be sure not to insert the brush into the holes themselves, as this could cause damage.

Reassembling and Reinstalling the Carburetor

Reinstalling the Float Bowl

Reinstall the float bowl, ensuring it's securely fitted and properly aligned. If necessary, you might need to gently tap it into place using a plastic hammer or the handle of your screwdriver.

AD

Reinstalling the Carburetor and Air Filter

Position the carburetor against the engine and reattach the fuel line at the inlet. Carefully hand tighten the carburetor mounting screws. Replace and reattach the air filter housing and filter in their respective positions.

Reconnecting the Spark Plug and Fuel Line

Reconnect the spark plug wire and lay it back in its proper position. Reattach the fuel line at the fuel tank, careful not to kink or pinch it.

After allowing the carburetor cleaner to evaporate (usually around 15-20 minutes), give your snowblower a test run. You should notice improved performance and a smoother-running engine. If not, double-check your work and consult your snowblower's user manual for further guidance.

Regularly cleaning your carburetor will help maintain your snowblower's performance and keep your winter chores running smoothly. Don't wait until spring – incorporate this maintenance task into your season-end snowblower storage routine, and you'll be ready to tackle next winter with ease.

AD