how to change the belt on shark navigator

Step-by-Step: Change Belts on Shark Navigator Vacuum

By Rachel King
AD

Do you own a Shark Navigator vacuum cleaner and find that it's not performing as well as it used to? The belt might be the culprit. Here's a comprehensive guide on how to change the belt on your Shark Navigator, ensuring that it's back to its powerful cleaning in no time.

Before we dive into the process, it's crucial to know that changing the belt on your Shark Navigator is a straightforward task that shouldn't take more than 15 minutes. Just follow these steps, and you'll be good to go.

Understanding the Shark Navigator Belt System

Your Shark Navigator has two belts: the primary drive belt and the smaller idler belt. The drive belt is responsible for powering the brushroll, while the idler belt keeps everything running smoothly. If either of these belts breaks or wears out, your vacuum's performance will significantly decrease.

AD
how to change belt on skark
how to change belt on skark
How to Easily Change the Belt on Shark Navigator: A Step-by-Step Guide - Vacuum Post
How to Easily Change the Belt on Shark Navigator: A Step-by-Step Guide - Vacuum Post
Shark Navigator Pet Pro Vacuum Cleaner User Manual
Shark Navigator Pet Pro Vacuum Cleaner User Manual

In this guide, we'll walk you through replacing both belts. However, if you've identified that only one belt needs replacement, you can follow the same steps for both, just stopping after you've replaced the belt that's giving you trouble.

Gather Your Tools

To perform this task safely and efficiently, you'll need a few tools:

Shark Navigator Roller Brush Compartment Replacement
Shark Navigator Roller Brush Compartment Replacement
EASY! Shark Vertex Cordless IZ462H Maintenance Guide
EASY! Shark Vertex Cordless IZ462H Maintenance Guide
  • A replacement belt kit for your Shark Navigator model. Make sure to get the correct kit for your specific model.
  • A flathead screwdriver

Prepare Your Vacuum

Before you start, ensure your Shark Navigator is unplugged and the bag or canister is empty. Also, make sure the brushroll is off, and the vacuum is upright to provide ample working space.

Now, let's get started with the belt replacement process.

AD

Step-by-Step Guide to Changing the Belts

Shark Navigator models vary slightly, so always refer to your user manual for the most accurate instructions. However, the following steps should apply to most Shark Navigator models.

Disassemble the Vacuum

Start by flipping your Shark Navigator onto its side. Look for a flathead screw on the bottom near the brushroll. Use your flathead screwdriver to remove this screw. Once the screw is out, the brushroll and turbine assembly should pop off easily.

Carefully lift off the cover to expose the belts. You might need to wiggle it a bit to free it from the vacuum's housing.

AD

Remove the Old Belts

Begin with the idler belt. It's usually the smaller, more brittle one. You can use your fingers or the tip of your screwdriver to pull it off the pulleys. Be careful not to lose any of the small springs or screws. Set the idler belt aside.

The primary drive belt will be the larger, black belt. To remove it, first, ensure the brushroll is not turning. Then, you can carefully pull it off the same pulleys, working from one side to the other.

Install the New Belts

First, install the new idler belt. Wrap it around the smaller pulley on the turbine housing and the back of the brushroll. Ensure the belt is fully seated on both pulleys and that the spring is secured.

AD

Next, install the drive belt. Wrap it around the larger pulley on the turbine housing and the front of the brushroll. Make sure the belt is fully seated on both pulleys and that the tension is even on both sides.

Reassemble and Test Your Shark Navigator

Before you put everything back together, double-check that all the belts are correctly installed and have the right amount of tension. Then, replace the cover and screw it back on.

Flip your Shark Navigator upright, plug it in, and test it out. You should hear the brushroll spinning again, and your vacuum should be ready for action.

With your Shark Navigator back to its powerful cleaning, you can now tackle those tough cleaning tasks with confidence. Regularly checking and maintaining your vacuum's belts will not only extend their lifespan but also keep your cleaning performance top-notch. Happy cleaning!

AD