how to change shark vacuum filter

Mastering Shark Vacuum Filters: A Step-by-Step Guide to Change

By Rachel Anderson
AD

If you're a proud owner of a Shark vacuum cleaner, you'll no doubt want to ensure it remains in top condition. A vital part of this maintenance is knowing how to replace the filter, which is often a common question among users. This guide will walk you through the process of changing your Shark vacuum filter, step by step.

Before we begin, it's essential to know that not all Shark vacuums are the same, and the filter location and replacement process might vary slightly depending on your model. However, the following steps should provide a general idea that can be adapted to your specific Shark vacuum.

Identifying Your Filter Type

Shark vacuums use two primary types of filters: the post-motor foam filter and the HEPA filter. The post-motor foam filter is located at the bottom of the dust canister, usually near the base, while the HEPA filter is found behind the dust canister.

AD
How To Clean Shark Vacuum Cleaner Filters 2023
How To Clean Shark Vacuum Cleaner Filters 2023
a person wiping up the dust off of a blender with a blue cloth on it
a person wiping up the dust off of a blender with a blue cloth on it
Quick Steps to Clean Your Shark Vacuum Filter Perfectly
Quick Steps to Clean Your Shark Vacuum Filter Perfectly

To identify your filter type, you'll need to access the filter compartment. For post-motor foam filters, simply remove the dust canister from your Shark vacuum. For HEPA filters, you'll need to detach the dust canister by pressing the release latches, then locate the HEPA filter behind it.

Changing the Post-Motor Foam Filter

After identifying the post-motor foam filter, you'll notice it's snugly fit. To remove it, gently squeeze the sides and pull it out. Be careful not to bend or tear the filter.

a person sitting on the floor holding a can and measuring something with a tape measure
a person sitting on the floor holding a can and measuring something with a tape measure
Shark Rotator Lift-Away Speed Filter Replacement
Shark Rotator Lift-Away Speed Filter Replacement

To replace the filter, take your new one and align the unique notches or arrows with those in the filter compartment. Push the new foam filter back into place, ensuring it's fully seated and secure.

Changing the HEPA Filter

To replace the HEPA filter, first, locate the filter's release tabs, usually on the sides or at the top. Press these tabs to release the filter from its compartment.

AD

Grab the HEPA filter by its sides and pull it out. Discard the old filter. Insert the new HEPA filter using the same upward swooping motion as the old one. Ensure the filter is correctly aligned with the lenticular look facing up. Push it back into place until you hear it click into position.

Cleaning Your Shark Vacuum Filter (if Reusable)

Some Shark vacuum filters are reusable. If yours is, you can attempt to clean it and use it again. However, keep in mind that the cleaning effect decreases with each use, and eventually, you'll need a new filter.

To clean the post-motor foam filter, give it a quick rinse under cold water and let it air-dry completely before replacing it. For HEPA filters, consult your owner's manual for specific cleaning instructions, as some may need to be professionally cleaned.

AD

Rinsing the Foam Filter

Under a faucet or in a sink, gently rinse the foam filter with cold water. Be careful not to use hot water, as it can damage the filter and affect its performance.

Once the foam filter is clean, lay it flat on a dry, clean towel to air-dry. Ensure it's completely dry before replacing it in your vacuum. It could take up to 24 hours to dry, so plan accordingly.

Professional Cleaning of HEPA Filters

If your HEPA filter is reusable, some Shark models recommend professional cleaning. You can take your filter to a professional service center, or some local stores may offer this service.

AD

Before taking your filter for professional cleaning, ensure you've followed any pre-cleaning instructions provided in your owner's manual. After the filter is cleaned, allow it to dry thoroughly before reinstalling it in your vacuum.

Remember, all filters will eventually wear out and need replacement, regardless of how well you maintain them. Always check your filters regularly and replace them when necessary to ensure your Shark vacuum is performing at its best.

Happy vacuuming, and here's to keeping your Shark cleaner, longer!

AD