how to change oil jeep grand cherokee

Change Oil Jeep Grand Cherokee: Step-by-Step Guide

By Christopher White
AD

If you're driving a Jeep Grand Cherokee, regular oil changes are crucial to maintaining its performance and longevity. The process might seem daunting, but with the right tools and a little elbow grease, you can change the oil in your Grand Cherokee in no time. This comprehensive guide walks you through the step-by-step process, ensuring you get the job done right.

Before we dive in, let's talk tools. You'll need a wrench, an oil filter wrench, a drain pan, new oil and oil filter, and gloves to protect your hands. Also, make sure your Grand Cherokee is completely cooled down before starting to avoid any burns. Let's get started.

Preparation and Gathering Materials

Before you start, make sure you have all the necessary materials. Check your Jeep Grand Cherokee's manual for the exact specifications, but generally, you'll need:

AD
How to change the oil and filter on a 2015 Jeep Grand Cherokee
How to change the oil and filter on a 2015 Jeep Grand Cherokee
How Many Quarts of Oil Does a Jeep Grand Cherokee Take: Essential Maintenance Guide
How Many Quarts of Oil Does a Jeep Grand Cherokee Take: Essential Maintenance Guide
2011-2025 Jeep Grand Cherokee Front & Rear Differential Oil Change & Transfer Case Fluid Replacement
2011-2025 Jeep Grand Cherokee Front & Rear Differential Oil Change & Transfer Case Fluid Replacement
  • 5 quarts of SAE 5W-30 or 5W-20 full synthetic, or 5W-30 synthetic blend motor oil
  • One oil filter

Don't forget to check the oil type your Grand Cherokee requires, and always use an oil filter that's designed for your specific vehicle.

Locating the Oil Drain Plug and Oil Filter

The oil drain plug is located at the bottom of the oil pan, near the front of the engine. Look for a large, bolt-like item with a washer on top. The oil filter is usually positioned near the front of the engine, close to the air filter.

1999-2004 Jeep Grand Cherokee WJ Oil and Oil Filter Replacement (1999, 2000, 2001, 2002, 2003, 2004)
1999-2004 Jeep Grand Cherokee WJ Oil and Oil Filter Replacement (1999, 2000, 2001, 2002, 2003, 2004)
How to Reset Oil Change on Jeep Grand Cherokee: Step-by-Step Guide for Owners
How to Reset Oil Change on Jeep Grand Cherokee: Step-by-Step Guide for Owners

Preparing the Oil and Oil Filter

Prepare the new oil filter by filling the oil filter with about 2/3 of a cup of new oil. This helps to pre-lubricate the filter and makes installation easier.

Draining the Old Oil

Place your drain pan underneath the oil drain plug. Using an appropriately sized wrench, loosen and remove the oil drain plug by turning it counterclockwise. Be careful, as the oil will start to drain immediately, and it may be hot.

AD

Cleaning the Oil Drain Plug and Area

Once all the oil has drained, use a rag or paper towels to clean the oil drain plug and the area around the oil pan. This helps you to inspect the plug and the area for any signs of damage or leaks.

Reinstalling the Oil Drain Plug

Once clean and dry, lightly grease the oil drain plug's threads using clean motor oil. Reinstall the plug by hand, turning it clockwise until it's snug, then tighten it with the wrench an additional 1/4 to 1/2 turn. Be careful not to overtighten.

Replacing the Oil Filter

Position the drain pan underneath the oil filter, as there may be some residual oil in the filter. Remove the oil filter by turning it counterclockwise. Once removed, fill the open end of the new filter with a small amount of new oil.

AD

Installing the New Oil Filter

Lightly grease the gasket of the new oil filter with clean motor oil, then screw it onto the engine by hand, turning it clockwise. Tighten the filter by turning it an additional 1/4 to 1/2 turn. Do not overtighten the filter, as this could cause it to leak or be difficult to remove during future oil changes.

Adding New Oil to the Engine

Locate the oil fill hole on top of the engine. It should be marked with an oil can or "OIL" symbol. Using a funnel, pour the new motor oil into the engine, alternating between adding a small amount and checking the oil level with the dipstick. Continue until the oil level is within the "FULL" range on the dipstick.

Start the engine and let it run for about a minute. This allows the new oil to circulate throughout the engine. Shut off the engine, give it a few minutes to settle, then check the oil level again. Add more oil if necessary, until it's within the "FULL" range on the dipstick.

AD

Resetting the Oil Life Monitor

Not all Jeep Grand Cherokee models have an oil life monitor, but if yours does, you'll need to reset it after an oil change. Consult your owner's manual for the exact process, but it usually involves turning the ignition on without starting the engine, then pressing and holding the trip odometer reset button until the oil life monitor displays "OIL LIFE:" and "100%."

That's it! You've successfully changed the oil in your Jeep Grand Cherokee. Regular oil changes are crucial to keeping your vehicle running smoothly and efficiently. Always consult your owner's manual for specific maintenance intervals and guidelines. Happy driving!

AD