how to change oil in mercury 4 stroke outboard

Step-by-Step: Change Oil in Mercury 4 Stroke Outboard

By Mark Allen
AD

Regular oil changes are crucial to the longevity and performance of your Mercury 4-stroke outboard motor. This comprehensive guide will walk you through a step-by-step process of how to change the oil in your Mercury 4-stroke outboard, ensuring it stays in top condition. Let's dive in!

Before you start, gather your tools and materials. You'll need a wrench or socket, an oil filter wrench, an oil collection pan, a funnel, gloves, and around 6.5 quarts of SAE 10W30 or 15W40 full synthetic motor oil, depending on your outboard's requirements. Make sure your engine and oil are at normal operating temperature for easier drainage.

Draining the Old Oil

The first step is to remove and discard the old oil. Locate the oil pan at the bottom of your outboard motor and place your oil collection pan beneath it.

AD
the motor cycle oil and gear lube change is being used to make it more expensive
the motor cycle oil and gear lube change is being used to make it more expensive
How to Maintain 4-stroke Outboards
How to Maintain 4-stroke Outboards
Mercury 40HP Fuel System Rebuild
Mercury 40HP Fuel System Rebuild

Using your wrench or socket, loosen and remove the oil pan drain plug by turning it counterclockwise. Allow the old oil to drain fully into the collection pan. Once drained, wipe the area clean and reinsert the drain plug, ensuring it's properly torqued to 20-25 ft-lbs.

Removing the Oil Fill Cap and Changing the Oil Filter

Next, remove the oil fill cap on top of the engine to relieve any remaining pressure. Using your oil filter wrench, loosen and remove the oil filter. If it's stuck, wrap a strap wrench orVue around it to break the seal. Discard the old filter.

a man standing next to a boat with lots of engines on it's back
a man standing next to a boat with lots of engines on it's back
How To: Mercury Outboard No Spark Step-By-Step how to fix with minimal tools.
How To: Mercury Outboard No Spark Step-By-Step how to fix with minimal tools.

Before installing the new oil filter, dip your finger in some new oil and rub it around the gasket of the new filter. This helps create a better seal and makes it easier toremove the filter the next time you change the oil. Screw on the new filter by hand, turning it clockwise until it's snug, then give it about ¾ to 1 turn - do not overtighten!

Refilling with New Oil

Now that the old oil and filter are out, it's time to refill with fresh oil. Pour the new oil through the fill hole at a steady, controlled pace, using a funnel to prevent spills. Allow the oil to settle for a few minutes between pours to give you a more accurate reading on the dipstick.

AD

Checking the Oil Level

After adding the appropriate amount of oil - typically 6.5 quarts for Mercury 4-strokes - allow it to settle for a few minutes, then check the oil level using the dipstick. Wipe the dipstick clean, reinsert it, and pull it out. The oil level should be within the "FULL" range on the dipstick. If it's below this mark, add a little more oil, allowing it to settle and checking again.

Remember to reattach the oil fill cap once you've reached the correct oil level. Run the engine for about a minute to check for any leaks at the oil pan drain plug or the oil filter. If all looks good, turn off the engine and allow the oil to settle for about 10 minutes before rechecking the oil level.

Resetting the Engine's Oil Light

After changing the oil, it's essential to reset your Mercury outboard's oil light to ensure it provides accurate maintenance reminders in the future. Consult your owner's manual for the specific procedure, as it differs between models. Typically, you'll need to cycle the engine's ignition and run it for a short period to reset the light.

AD

Finally, dispose of the used oil responsibly by taking it to a recycling center or a service station that accepts used oil. Never pour used oil down drains or into the water.

There you have it - a comprehensive guide on how to change the oil in your Mercury 4-stroke outboard motor. Regular oil changes are the key to keeping your engine running smoothly and extending its lifespan. Be sure to consult your owner's manual for specific details about your model and engine requirements. Happy boating!

AD