how to change oil in john deere riding mower

Step-by-Step Guide: Change Oil in John Deere Riding Mower

By Michael Rodriguez
AD

Regular maintenance is key to keeping your John Deere riding mower in top shape, and one of the most important tasks is changing the oil. This not only ensures the longevity of your mower's engine but also keeps it running smoothly. Here's a step-by-step guide to help you change the oil in your John Deere riding mower.

Before we dive into the process, ensure you have the following tools and materials ready: a wrench (size may vary depending on your mower model), an oil filter wrench, an oil drain pan, a large funnel, new oil filter, and about 1.9 liters (or 20W50 or SAE 30 motor oil). Always refer to your mower's owner's manual for exact specifications.

Preparation

Find a safe and well-lit workspace to perform this task. Start by allowing the engine to run for a few minutes to warm up the oil, making it easier to drain.

AD
John Deere's 30-Second Oil Change Turns This Task Into a One-Handed, Half-a-Minute Job
John Deere's 30-Second Oil Change Turns This Task Into a One-Handed, Half-a-Minute Job
HOW TO Change John Deere D130 Oil Change Riding Lawn Mower Maintenance
HOW TO Change John Deere D130 Oil Change Riding Lawn Mower Maintenance
How to Change the Easy Change Oil System | John Deere
How to Change the Easy Change Oil System | John Deere

Once the engine is warmed up, turn off the mower and wait for about 15-20 minutes to allow the oil to cool down and settle. This will make the oil less likely to scorch your hands when you remove the drain plug.

Draining the Old Oil

Place your drain pan beneath the oil pan, located at the bottom of the engine. Using your wrench, turn the oil pan drain plug counterclockwise to remove it. Allow the oil to drain completely into the pan. This may take a few minutes.

John Deere Easy Oil Change Conversion On Lawn Tractor
John Deere Easy Oil Change Conversion On Lawn Tractor
FAST! How to Change the Oil in a John Deere L110 in 10 Minutes!
FAST! How to Change the Oil in a John Deere L110 in 10 Minutes!

While the oil is draining, inspect the oil pan drain plug and gasket for any signs of wear or damage. Replace them if necessary to ensure a proper seal when you reinstall them.

Reinstalling the Drain Plug

Once all the oil has drained, wipe the area clean using a lint-free cloth or shop rag. Carefully reinsert and tighten the drain plug by hand initially, then snug it with the wrench. Be cautious not to overtighten as this can strip the threads or crack the oil pan.

AD

Check your mower's owner's manual for the exact torque specification, but typically, it should be tightened to about 25-35 foot-pounds (around 3 to 4.5 NMDA).

Replacing the Oil Filter

Locate the oil filter beneath the mower, usually attached to the engine's right side. Using the oil filter wrench, turn the filter counterclockwise to remove it. You may need to use some force, so be prepared.

Before installing the new filter, wipe off any excess oil from the filter mounting surface and the new filter's rubber gasket. Hand-tighten the new oil filter by turning it clockwise onto the oil filter mounting surface. Consult your owner's manual for the exact torque specification, usually around 12-25 foot-pounds (1.6 to 3.4 NMDA).

AD

Adding New Oil

With the new oil filter in place, locate the oil fill hole on top of the engine. Using your funnel, slowly pour the recommended amount of oil into the engine, allowing gravity to do most of the work.

It's essential to leave about an inch of clearance from the top of the oil fill hole to avoid overfilling. After pouring the oil, allow it to settle for a few minutes before rechecking the oil level using the dipstick.

Rechecking the Oil Level

Pull the dipstick out, wipe it clean, and reinsert it all the way back into the oil fill hole. Remove it again and check the oil level. The correct oil level should be within the "FULL" range on the dipstick.

AD

If the oil level is below the "FULL" mark, gradually add more oil until the level is within this range. If you've added too much oil, you may need to drain some out until the level is correct.

Once you've correctly set the oil level, turn on the mower and let it run for a few minutes. Check for any leaks around the oil drain plug and oil filter areas. Turn off the mower and wait a few minutes for the oil to settle before rechecking the oil level one last time. If everything looks good, you're all set! Regularly changing your John Deere riding mower's oil will help keep it running smoothly and extend its lifespan.

AD