how to change oil in craftsman lawn mower

Step-by-Step: Change Oil in Craftsman Lawn Mower

By Amanda Robinson
AD

Regular maintenance is key to keeping your Craftsman lawn mower in top shape, and one of the most crucial tasks is changing the oil. While it might seem daunting, changing your mower's oil is a straightforward process that you can do at home, saving you time and money. Here's a step-by-step guide to help you change the oil in your Craftsman lawn mower safely and effectively.

Before we start, gather your tools and materials. You'll need a wrench that fits your oil drain plug (usually 13mm or 14mm for Craftsman mowers), an oil filter wrench, an oil catch pan, new oil (SAE 30 is recommended for most Craftsman mowers), and a new oil filter. Ensure you have the correct oil and filter for your mower model. Consult your owner's manual if you're unsure.

Preparation

First, ensure your Craftsman lawn mower is on a flat, stable surface, and the engine is cool to avoid any burns. Disconnect the spark plug wire to prevent the engine from starting accidentally. You can also remove the air filter to have easier access to the oil drain plug.

AD
How to Change the Oil in a Craftsman Lawnmower
How to Change the Oil in a Craftsman Lawnmower
How to Change Craftsman Lawn Mower Oil and Filter | LTS 2000
How to Change Craftsman Lawn Mower Oil and Filter | LTS 2000
Change the Oil & Tune Up Lawnmower - GardenFork.T
Change the Oil & Tune Up Lawnmower - GardenFork.T

Position your oil catch pan underneath the oil drain plug, located at the bottom of the engine block. The plug may be concealed by a plastic cap; remove it if necessary.

Draining the Old Oil

Using your wrench, loosen the oil drain plug by turning it counterclockwise. Be careful, as the oil may be hot. Allow the old oil to drain completely into the catch pan. This could take a few minutes. It's crucial to remove all the old oil to ensure your new oil performs optimally.

Troubleshooting A Riding Lawn Mower That Won't Start
Troubleshooting A Riding Lawn Mower That Won't Start
How to Change the Oil in a Push Lawnmower (Example: Craftsman, Murray, Briggs & Stratton Engines)
How to Change the Oil in a Push Lawnmower (Example: Craftsman, Murray, Briggs & Stratton Engines)

While you're waiting for the oil to drain, you can prepare the new oil filter. Lubricate the gasket of the new filter with some new oil. This will help create a better seal and make the installation process easier.

Replacing the Oil Filter

Once the old oil has drained, clean the oil drain plug and area around it to remove any debris or old oil residue. Reinstall the oil drain plug by hand, snugging it finger-tight. Once it's snug, give it a final turn using the wrench, being careful not to overtighten. The exact torque specification can be found in your owner's manual but is typically around 1/4 to 1/3 of a turn after snugging.

AD

Now, remove the old oil filter. If it's tight, use the oil filter wrench. Before installing the new oil filter, ensure the rubber gasket is in good condition. If it's damaged, replace the filter. Position the new oil filter onto the engine block, and hand-tighten it until it's snug. Similar to the oil drain plug, the final turn should be around 1/4 to 1/3 of a turn after snugging.

Adding New Oil

Locate the oil fill hole near the top of the engine block, identified by an oil can symbol or the word "OIL". Remove the oil fill cap and use a funnel to pour the new oil into the engine. Add the recommended amount of oil for your mower model, which can vary. Again, consult your owner's manual if you're unsure.

After adding the oil, replace the oil fill cap and wait a few minutes for the oil to settle. Check the oil level using the dipstick. Craftsman mowers typically have a "FULL" mark and an "ADD" mark. The oil level should be somewhere between these two marks when the engine is cool. If the oil level is below the "FULL" mark, add more oil in small increments, checking the level again after each addition.

AD

Final Checks

Once the oil level is correct, reattach the spark plug wire and air filter. Start the engine and let it run for a few minutes to allow the new oil to circulate. Turn off the engine and wait a few minutes for the oil to settle. Re-check the oil level and, if necessary, add more oil to maintain the correct level.

Congratulations, you've successfully changed the oil in your Craftsman lawn mower! Regular oil changes will keep your mower running smoothly and prolong its lifespan. Always consult your owner's manual for the recommended oil change interval, but as a general rule, change the oil after the first five hours of use and then every 50 hours thereafter, or once a year, whichever comes first.

Now that your mower is well-maintained, it's ready to tackle even the toughest lawn chores. Happy mowing!

AD
AD