how to change oil on a craftsman riding mower

Step-by-Step: Change Oil on Craftsman Riding Mower

By Thomas Thompson
AD

Regular maintenance is key to the longevity and performance of your Craftsman riding mower. One essential task is changing the oil, which helps keep your engine running smoothly and efficiently. In this comprehensive guide, we'll walk you through the process of changing the oil on your Craftsman riding mower in a simple, step-by-step manner.

Before we begin, make sure you have the following tools and materials ready: a new oil filter, 2.5 quarts of SAE 5W-30 motor oil (or the type recommended by your mower's manual), a 13mm socket wrench, an oil filter wrench, an oil drain pan, funnel, and gloves to protect your hands from oil and dirt.

Preparing Your Craftsman Riding Mower

Ensure your mower is on a flat surface and has cooled down for at least 30 minutes to prevent any burns. Engage the parking brake and remove the ignition key to ensure the mower won't start accidentally.

AD
How to Change the Oil in a Craftsman Lawnmower
How to Change the Oil in a Craftsman Lawnmower
How to do a oil change on a riding lawn mower
How to do a oil change on a riding lawn mower
How to Change Craftsman Lawn Mower Oil and Filter | LTS 2000
How to Change Craftsman Lawn Mower Oil and Filter | LTS 2000

Gather your tools and materials underneath the mower's oil pan, which is located at the bottom of the engine. The oil pan is often indicated by a sketch of an oil can on the mower's frame.

Draining the Old Oil

Position your oil drain pan underneath the oil pan. Using your 13mm socket wrench, loosen the oil pan drain plug by turning it counterclockwise. Remove the drain plug by hand once it's loose enough, allowing the old oil to drain into the pan.

John Deere's 30-Second Oil Change Turns This Task Into a One-Handed, Half-a-Minute Job
John Deere's 30-Second Oil Change Turns This Task Into a One-Handed, Half-a-Minute Job

Be patient, as this may take a few minutes. Once the oil has finished draining, wipe the area clean with a cloth or paper towel. Reinstall and tighten the oil pan drain plug using your hand and the 13mm socket wrench. Ensure it's snug but avoid overtightening.

Removing the Old Oil Filter

Locate the oil filter, which is usually found near the oil pan. Place your oil drain pan underneath the filter to catch any residual oil. Using your oil filter wrench, turn the filter counterclockwise to remove it. You may need to use both hands and apply some force.

AD

Once the oil filter is off, discard it. Use a cloth or paper towel to clean the area around the new oil filter's planting point on the engine. This will help establish a better seal and prevent leaks.

Installing the New Oil Filter and Adding New Oil

Rub a small amount of new motor oil around the rubber gasket of the new oil filter. This helps create a better seal and ensures the filter is properly lubricated during installation. Hand-tighten the new oil filter onto the engine by turning it clockwise. It should be snug but not overtightened.

Using your funnel, pour the recommended amount of new motor oil into the oil fill hole, which is located at the top of the engine. Replace the oil fill cap once you've added the correct amount of oil.

AD

Checking the Oil Level

Allow the oil to settle for a few minutes, then check the oil level using the dipstick. The oil fill hole is usually marked with an "O" or "Engine Oil" label, and the dipstick has "FULL" and "ADD" marks. Wipe the dipstick clean, then reinsert it and remove it again to check the oil level.

If the oil level is below the "FULL" mark, add more oil in small increments, checking the level each time, until it reaches the "FULL" mark. If it's above the "FULL" mark, you'll need to drain some oil to avoid overfilling. Be careful not to add too much oil, as this can cause problems with your engine.

After changing the oil, start the engine and let it run for about a minute. This will allow the new oil to circulate throughout the engine. Shut off the engine and wait a few minutes for the oil to settle again. Recheck the oil level and add more oil if necessary. This time, you should be within the "FULL" range.

AD

Your Craftsman riding mower is now ready to tackle the season's lawn care tasks with renewed vigor. Regular oil changes are key to maintaining your mower's performance and extending its lifespan. As always, consult your mower's owner's manual for specific details about your model's oil change needs. Happy mowing!

AD