how to change oil harley sportster

How to Change Oil on a Harley Sportster: Step-by-Step

By Emily Thomas
AD

Changing the oil on your Harley Sportster is a crucial maintenance task that ensures your bike's engine remains in top condition. While it might seem daunting, especially if you're new to motorcycles, it's a straightforward process that you can master at home. Here, we'll guide you through a step-by-step process, with all the tools and materials you'll need.

Oil changes are recommended every 3,000 to 5,000 miles for Harley Sportsters, depending on weather conditions and riding habits. Regularly checking your oil level and condition can help you determine if it's time for a change.

Preparation and Gathering Tools

Before you start, ensure you have all the necessary tools and materials. Gathering everything ahead of time will make the process smoother and more efficient.

AD
How To: Harley-Davidson Sportster Oil & Filter Change - YouMotorcycle
How To: Harley-Davidson Sportster Oil & Filter Change - YouMotorcycle
How To Change Motor Oil in a Harley Davidson Sportster 1200
How To Change Motor Oil in a Harley Davidson Sportster 1200
Harley-Davidson Sportster Evolution Transmission/Primary Oil Change
Harley-Davidson Sportster Evolution Transmission/Primary Oil Change

Tools you'll need:

  • 14mm socket wrench or oil filter wrench
  • filter wrench
  • oil catch pan
  • gloves
  • goggles or safety glasses

Materials you'll need:

a person is holding the handlebars on a motorcycle
a person is holding the handlebars on a motorcycle
How To Change Oil & Filter on Harley Sportster!
How To Change Oil & Filter on Harley Sportster!
  • New oil filter
  • SAE 20W-50 or 15W-60 (or the oil type recommended in your owner's manual) Harley Sportster motorcycle oil

Preparing Your Bike

First, ensure your Harley Sportster is on a level surface and the engine has been off for at least 30 minutes. This allows the oil to settle and makes it easier to drain.

Next, remove the oil fill cap on the bike's left side, near the airbox. This will minimize pressure when you remove the oil drain plug and prevent any oil spills.

AD

Draining the Oil

Place your oil catch pan underneath the oil pan on the bottom left side of your Sportster. Use your 14mm socket wrench to loosen and remove the oil drain plug by turning it counterclockwise. Allow the oil to completely drain, which may take several minutes.

Once all the oil is drained, clean the area and the oil drain plug to remove any remaining oil. You can use a shop towel or some steel wool for this task. Wipe off the oil pan as well, as this will help you detect any potential leaks after the new oil has been added.

Installing the New Oil Filter

Before installing the new oil filter, lightly coat its rubber gasket with new oil. This helps provide a better seal and makes it easier to remove the filter during future oil changes.

AD

Thread the new oil filter onto the engine's oil filter base by hand, turning it clockwise. Once the gasket touches the base, continue turning it another ¾ to 1 ½ turns. This is known as seating the gasket. Be careful not to overtighten, as this can damage the gasket and cause a leak.

Adding New Oil

Clean the area around the oil fill hole to prevent any contaminants from entering the engine. Replace the oil fill cap and add the recommended amount of oil, starting with two-thirds of the total amount. This allows room for the oil to expand when the engine heats up.

With the oil fill cap removed, start your bike and let it run for about a minute. This helps the oil move through the engine and allows you to get a more accurate oil level reading.

AD

Checking the Oil Level

After the engine has run for a minute, turn it off and let it sit for about five minutes to allow the oil to settle. Wipe the dipstick clean, reinsert it, and then remove it again to check the oil level.

The oil level should be within the "FULL" range on the dipstick. If it's low, add more oil in small increments until it reaches the "FULL" mark. Always keep track of how much oil you've added and adjust your oil levels accordingly.

Final Touches

Reinstall the oil fill cap and give your Sportster a quick once-over to ensure there are no leaks. Start the bike and check for any signs of oil on the engine or oil filter. If everything looks good, you're ready to ride again!

Always keep an eye on your oil level and condition between oil changes. Regular oil changes, along with proper lubrication and occasional tune-ups, will keep your Harley Sportster running smoothly and safely for many miles to come.

AD