how to change jeep wrangler oil

How to Change Jeep Wrangler Oil: Step-by-Step Guide

By Mark White
AD

Eager to keep your Jeep Wrangler running smoothly and ready for both city and off-road adventures? Regular oil changes are crucial to maintain its performance and longevity. Here's a comprehensive guide on how to change your Jeep Wrangler's oil, ensuring top quality care for your rugged beast.

Before you dive in, gather these materials: new oil filter, 5W-20 or 5W-30 (or as per your Jeep's specs) full synthetic motor oil, a 13mm socket wrench, an oil filter wrench, a funnel, a jack and jack stands, an oil drain pan, gloves, and safety glasses.

Preparation and Draining the Old Oil

First, ensure your Jeep is on a level surface and has cooled down to prevent any burns. Using a jack and jack stands, lift the vehicle and secure it.

AD
Why Is My Jeep Wrangler Leaking Oil?Explained!
Why Is My Jeep Wrangler Leaking Oil?Explained!
How to Change the Oil in your 3.6L V6 Jeep Wrangler JL or Jeep Gladiator JT
How to Change the Oil in your 3.6L V6 Jeep Wrangler JL or Jeep Gladiator JT
How to Change Oil on Jeep Wrangler
How to Change Oil on Jeep Wrangler

Position your oil drain pan underneath the oil pan, located at the bottom of your Jeep's engine. Using a 13mm socket wrench, loosen and remove the oil pan drain plug by turning it counterclockwise. Allow the oil to drain completely.

Removing the Old Oil Filter

The oil filter is typically located near the oil pan. Place your oil filter wrench on the oil filter, turn it counterclockwise until it's loose, then finish removing it by hand. Be prepared for some subsequently draining oil.

Jeep Wrangler 4.0 Oil Capacity & Type: Explained!
Jeep Wrangler 4.0 Oil Capacity & Type: Explained!
DIY Jeep Wrangler Oil Change 2012-2018
DIY Jeep Wrangler Oil Change 2012-2018

Wipe the mounting surface clean to ensure a proper seal for the new oil filter. If it's too tight to remove by hand, use the wrench, but be careful not to damage it.

Installing the New Oil Filter and Drain Plug

Apply a thin layer of new engine oil around the gasket of the new oil filter. Screw it on by hand, turning it clockwise until it's snug, then give it about 3/4 of a turn counterclockwise to ensure proper tension - too tight can strip the gasket, and too loose can cause leaks.

AD

Replace and tighten the oil pan drain plug by hand initially, then snug it using the socket wrench. Be careful not to overtighten as this can cause damage or oil leaks. Wipe any remaining oil from the underside of the engine.

Adding New Oil

Lower your Jeep and let it sit for about 15 minutes to allow the new oil to settle, then check the oil level using the dipstick. Wipe it clean, insert it all the way, remove it, and check the level. It should be within the 'FULL' range on the dipstick.

If the level is low, add the appropriate amount of oil (usually between 4 to 5 quarts for a Jeep Wrangler) in small increments, allowing the oil to settle after each addition. Recheck the level and adjust if needed.

AD

Resetting the Oil Change Light and Final Checks

Reset your Jeep's oil change light according to your owner's manual, usually by turning the ignition on without starting the engine, then turning it off and on again.

Start the engine and let it run for about a minute, then check for any leaks underneath the vehicle. Turn off the engine and wait another 15 minutes for the oil to settle, then recheck the oil level and add more if necessary.

There you have it! Your Jeep Wrangler's oil change is complete, and it's primed for your next off-road adventure. Don't forget to dispose of the used oil and filter responsibly at a certified recycling center. Happy trails!"

AD
AD