how to change chain on husqvarna chainsaw

Step-by-Step: How to Change a Chain on Your Husqvarna Chainsaw

By Steven Taylor
AD

Regular maintenance of your Husqvarna chainsaw is crucial for optimal performance and longevity, with changing the chain being a key part of this process. This step-by-step guide will walk you through the process of how to change a chain on your Husqvarna chainsaw, ensuring you maintain the highest safety standards and achieve the best results.

Firstly, it's important to note that this procedure should only be carried out when the chainsaw is cold, and there's no residual gas in the cylinder. Always follow the safety guidelines outlined in your Husqvarna chainsaw manual to ensure a safe and efficient process.

Preparation: Safety First

Before you begin, make sure to gather all the necessary tools. You'll need a new chain suitable for your saw, a scrench (combination screwdriver and wrench), a bar and chain assembly tool (if necessary), and safety glasses to protect your eyes from debris.

AD
How to Start & Change a Bar & Chain on Husqvarna Chainsaw 562xp & 142 Model Wood Cutting 562 xp
How to Start & Change a Bar & Chain on Husqvarna Chainsaw 562xp & 142 Model Wood Cutting 562 xp
How to Reset the Chain Brake on a Chainsaw | Husqvarna
How to Reset the Chain Brake on a Chainsaw | Husqvarna
How to Replace the Chain on a Chainsaw: 11 Steps (with Pictures)
How to Replace the Chain on a Chainsaw: 11 Steps (with Pictures)

Ensure your Husqvarna chainsaw is on a stable, flat surface and that the chain brake is engaged to prevent any unwanted startup during the process.

Dismounting the Old Chain

Begin by locating the chain adjustment screw, typically found at the base of the chain guide bar. Using your scrench, loosen this screw by turning it counterclockwise. This will release the tension on the chain, allowing you to slide it off the guide bar.

How To Adjust A Husqvarna Chainsaw Oiler - Hunker
How To Adjust A Husqvarna Chainsaw Oiler - Hunker
Filing the chain - Husqvarna Chainsaw Academy
Filing the chain - Husqvarna Chainsaw Academy

Next, using your hands, carefully slide the old chain off the guide bar. If the chain is too tight, you may need to use your hands to pull the drive links away from the bar until the chain slackens enough to remove. Once off, set the old chain aside for disposal.

Inspecting and Cleaning the Bar

Before installing the new chain, it's essential to inspect and clean the guide bar. Check for any damage or signs of wear, such as flat or rounded edges on the Depth Gauge and rakers. If necessary, lubricate the grooves to ensure the new chain runs smoothly.

AD

If the guide bar is dirty, use a wire brush or compressed air to clean off any debris. This will prevent any friction or potential damage to the new chain during operation.

Installing the New Chain

With your guide bar clean and inspected, it's time to install the new chain. Begin by laying the new chain onto the guide bar, ensuring the drive links line up with the corresponding sprocket teeth. Align the chain so the cutting teeth face the correct direction.

At this stage, you might want to use a chain install tool, if available, to keep the chain aligned and tensioned as you progress. This will make the process smoother and more accurate.

AD

Securing the Chain onto the Bar

Once the chain is aligned, begin to wrap it around the guide bar, using your hands to keep it in place. Ensure the drive links remain engaged with the sprocket teeth throughout the process. When you reach the adjustment screw, insert the end of the chain into the link slot and continue to wrap the chain around the bar until it encerrcles the bar completely.

Engage the drive links with the sprocket teeth one last time to ensure the chain is correctly positioned. At this point, you should have the chain fully wrapped around the guide bar, ready for tensioning.

Tensioning the New Chain

Now it's time to tension the new chain. Using the scrench, tighten the adjustment screw by turning it clockwise. Tension the chain until there is just enough slack to pull the top chain off the bar with moderate force. You should aim for about 0.020" (0.5mm) of play between the top of the chain and the bar.

AD

Once adjusted, secure the tension with a slight turn of the screw in a counterclockwise direction. This final adjustment ensures the chain remains tightly secured without being too tight and causing unnecessary resistance during operation.

Post-Installation: Testing and Lubrication

With the new chain installed and tensioned, you're ready for a test run. Ensure your Husqvarna chainsaw is still on a stable surface, and that the chain brake is engaged. Make a few test pulls of the starter rope to ensure the chainsaw runs smoothly and that the chain turns freely without any resistance.

After testing, lubricate the chain using a suitable Husqvarna bar and chain oil. Apply a light coat along the cutter and depth gauge, ensuring the entire length of the chain is well-oiled. This will help prevent friction, wear, and tear, ensuring your new chain performs at its best for longer.

Regularly inspecting and maintaining your Husqvarna chainsaw's chain is vital for optimal performance and safety. By following this guide, you'll not only learn how to change a chain on your Husqvarna chainsaw but also develop a sound understanding of the maintenance process that will keep your saw in top condition for years to come. Happy chainsawing!

AD