how to change blades on a husqvarna riding mower

Step-by-Step: Changing Blades on Your Husqvarna Riding Mower

By Hannah Williams
AD

When the blades on your Husqvarna riding mower become dull, it's time to replace them for optimal performance and safety. Regular blade maintenance ensures your lawn stays healthy and looking its best. Let's guide you through the process:

First, make sure to go through your Husqvarna mower's user manual for specific instructions and safety information tailored to your model. Now, let's dive into the step-by-step process of changing your mower's blades.

Preparation Before Changing Blades

Before you begin, ensure your mower is off and the blades have stopped spinning completely. Disconnect the spark plug wire to prevent accidental starting. Also, engage the parking brake and remove the key from the ignition.

AD
How To Tighten Drive Belt On Husqvarna Riding Mower? | Pad Outdoor
How To Tighten Drive Belt On Husqvarna Riding Mower? | Pad Outdoor
How to Replace the Cutting Blades on a Husqvarna Lawn Tractor
How to Replace the Cutting Blades on a Husqvarna Lawn Tractor
How to Change the Blades on a Riding Mower
How to Change the Blades on a Riding Mower

Once your mower is safe and secure, locate the grindplate underneath the mower, and place a suitable block of wood under one side of the deck to keep the mower steady while you work.

Removing the Old Blades

First, use a socket wrench to loosen and remove the retention bolt located on the bottom of the mower deck. This bolt secures the blade to the blade adapter. Be careful not to lose the lock washer and any spacers that might be present.

How to Change Husqvarna Riding Lawn Mower Blades
How to Change Husqvarna Riding Lawn Mower Blades

With the bolt removed, you can lift the blade away from the adapter. You might need to use a hammer to gently tap the blade adapter to release the blade, if it's stuck. Remember, the sharp side of the blade is facing up, so be cautious when handling it.

Clean and Inspect the Blade Adapter

Now's a good time to clean the blade adapter and check its condition. Use a wire brush to remove any debris or grass buildup. Inspect the adapter for any signs of wear or damage. If necessary, replace the adapter before installing the new blade.

AD

Also, this is a good opportunity to sharpen the old blade, if it's not too badly damaged. Using a blade sharpening tool, carefully sharpen the cutting edge. If the blade is damaged or dulled beyond repair, consider recycling it responsibly.

Installing the New Blades

Before you install the new blade, ensure it's the correct one for your mower model. Each Husqvarna riding mower uses a specific blade type with a unique part number, so always double-check.

Align the new blade with the blade adapter, ensuring the arrow on the blade matches the direction indicated on the adapter. The cutting edge of the blade should also be pointing in the direction of rotation (check your user manual if you're unsure).

AD

Securing the New Blade

Once the new blade is aligned correctly, insert the retention bolt and temporarily screw it back into place using your hand. Ensure the lock washer and any necessary spacers are correctly positioned.

Now, use a socket wrench to tighten the bolt securely. Do not overtighten, as this can cause the bolt to strip or the blade to wobble. The manual for your specific Husqvarna riding mower should provide the appropriate torque specs for the blade bolt.

Checking Your Work

Give the blade a gentle tug to ensure it's secure and not spinning loosely. Remove the block of wood holding up the mower deck, and lower the mower gently to the ground.

AD

Before you start mowing, run your Husqvarna riding mower through its paces in an open, clear area to ensure the new blade is spinning smoothly and evenly. If everything checks out, you're ready to tackle your lawn with a fresh set of blades.

Regular blade maintenance will not only keep your lawn looking fantastic but will also extend the lifespan of your Husqvarna riding mower. Happy mowing!

AD