how to change a belt on a kenmore dryer

Kenmore Dryer Belt Change: Step-by-Step Guide

By Hannah Smith
AD

Have you noticed your Kenmore dryer's belt making unusual noises or not performing as efficiently as before? It might be time to replace the belt to get your dryer running smoothly again. Changing a belt on a Kenmore dryer is a simple task that you can do yourself, saving you money on professional repair services. Let's dive into a step-by-step guide to help you through this process.

Before you start, ensure you have the necessary tools and the correct belt for your dryer model. Consult your Kenmore dryer's manual or look for the model number online to find the appropriate replacement belt. Gather these tools: a screwdriver, pliers, and perhaps a putty knife to help with the process.

Safety First: Preparation

Safety is paramount when working with appliances. Begin by unplugging your dryer from the power source to avoid any electrical hazards. Additionally, turn off the gas supply if you have a gas dryer and locate the gas valve toturn it back on once you're finished.

AD
How to Replace the Belt on a Kenmore 70 Series Dryer
How to Replace the Belt on a Kenmore 70 Series Dryer
How to Replace a Kenmore Gas Dryer Drive Belt
How to Replace a Kenmore Gas Dryer Drive Belt
How to Replace the Belt on a Kenmore 90 Series Dryer
How to Replace the Belt on a Kenmore 90 Series Dryer

Next, empty your dryer's lint trap and clean the area around the dryer. This will provide you with a clean and safe working environment. Now that you're all set, let's move on to disassembling your dryer.

Disassembling Your Kenmore Dryer

Start by removing the dryer's back panel. Most Kenmore dryers have screws on the top or sides of the back panel. Use your screwdriver to remove these screws, and then gently pull the panel off. You might need to use a putty knife to help release the panel if it's stuck.

How to Replace a Kenmore Electric Dryer Drive Belt
How to Replace a Kenmore Electric Dryer Drive Belt
Dryer Belt Replacement
Dryer Belt Replacement

Once the back panel is off, you'll see the belt, drum, and motor. The belt may be attached to the motor pulley or the drum, so you might need to loosen the motor or drum restraint bolt with your screwdriver to release the tension on the belt. This will make it easier to remove the old belt.

Removing the Old Belt

With the tension released, use your pliers to grab the old belt and pull it off the motor pulley and the drum. If the belt is broken or damaged, you might need to use a little force. Just be careful not to damage any other components in the process.

AD

Once the old belt is removed, inspect the interior of the dryer, especially the area where the belt was located. Look for any debris or damage that might have occurred during the belt's removal. Use a vacuum or cloth to clean up the area, ensuring no obstructions will interfere with the new belt's performance.

Installing the New Belt

Now that the old belt is removed and the interior is clean, it's time to install the new belt. Start by positioning the new belt around both the motor pulley and the drum. Make sure the belt is properly aligned and seated on both components.

Recheck the belt's position to ensure it's correctly placed on the pulleys. Once you're satisfied with its alignment, gently tighten the motor or drum restraint bolt to apply tension to the new belt. You don't need to over-tighten the bolt; a slight pull on the belt (around 1/2 inch to 1 inch) should be sufficient.

AD

Reassembling Your Kenmore Dryer

With the new belt in place and the correct tension applied, it's time to reattach the back panel. Carefully align the back panel with the dryer's body and secure it using the screws you removed earlier. Make sure the screws are fully tightened to ensure a secure fit.

Finally, reattach the outer covering of the dryer, replace the lint trap, and plug in your dryer. If you have a gas dryer, turn the gas supply back on at the valve. Double-check that everything is correctly connected and secure before running a test cycle.

Testing the New Belt

To ensure the new belt is working correctly, run a test cycle on your dryer. Load some laundry into the drum, set the dryer to a low heat setting, and start the cycle. Listen for any unusual noises, and monitor the dryer's performance to see if it's drying your laundry effectively.

AD

If the dryer performs as expected, congratulate yourself on a job well done! You've successfully changed the belt on your Kenmore dryer and saved money by performing the repair yourself. If you encounter any issues, don't hesitate to consult a professional technician for assistance.

Regular maintenance, like replacing worn-out belts, is essential to keep your Kenmore dryer running efficiently and prolong its lifespan. Stay proactive in caring for your appliance, and you'll enjoy many years of reliable performance. Happy DIYing!

AD